Toyota Venza manuals

Toyota Venza: Reassembly

REASSEMBLY

PROCEDURE

1. INSTALL FRONT SIDE MARKER LIGHT BULB

(a) Install the front side marker light bulb to the front side marker light socket.

(b) Turn the front side marker light socket with the front side marker light bulb in the direction indicated by the arrow shown in the illustration to install them as a unit.


2. INSTALL FRONT TURN SIGNAL LIGHT BULB

(a) Install the front turn signal light bulb to the front turn signal light socket.

(b) for Halogen Headlight:

(1) Turn the front turn signal light socket with the front turn signal light bulb in the direction indicated by the arrow shown in the illustration to install them as a unit.


(c) for HID Headlight:

(1) Turn the front turn signal light socket with the front turn signal light bulb in the direction indicated by the arrow shown in the illustration to install them as a unit.


3. INSTALL NO. 1 HEADLIGHT BULB (for Halogen Headlight)

(a) Turn the No. 1 headlight bulb in the direction indicated by the arrow shown in the illustration to install it.

NOTICE:

Do not touch the bulb glass.


4. INSTALL NO. 2 HEADLIGHT BULB (for Halogen Headlight)

(a) Turn the No. 2 headlight bulb in the direction indicated by the arrow shown in the illustration to install it.

NOTICE:

Do not touch the bulb glass.


5. INSTALL DISCHARGE HEADLIGHT BULB (for HID Headlight)

(a) Set the discharge headlight bulb to the headlight unit.

NOTICE:

Do not touch the bulb glass.

(b) Lock the set spring to install the discharge headlight bulb as shown in the illustration.


6. INSTALL LIGHT CONTROL ECU (for HID Headlight)

(a) Turn the socket of the light control ECU in the direction indicated by the arrow shown in the illustration to connect it.

NOTICE:

  • Check that the O-ring is installed on the light control ECU.
  • Check that the O-ring is not damaged or contaminated with foreign matter. If there is any damage, replace the O-ring with a new one.
  • Do not pull the light control ECU with the socket connected.

(b) Check that the red line on the output harness is not twisted and store the harness in the headlight assembly securely so that the output harness is not pinched.

Text in Illustration

*1

Red Line

(c) Turn the light control ECU in the direction indicated by the arrow shown in the illustration until the lock marks are aligned to install it.

Text in Illustration

*1

Lock Mark

NOTICE:

  • To prevent incomplete installation, make sure to fully push in and turn the light control ECU until the lock marks are aligned.
  • Do not apply excessive force using a tool.

Adjustment
ADJUSTMENT CAUTION / NOTICE / HINT HINT: It is possible that a bulb is incorrectly installed, affecting headlight aim. Bulb installation should be considered prior to performing the adjustment pr ...

Installation
INSTALLATION PROCEDURE 1. INSTALL HEADLIGHT ASSEMBLY (a) Connect each connector. (b) Install the headlight assembly with the bolt and 3 screws. Torque: 3.6 N·m {37 kgf·cm, 32 in·lbf} 2. INS ...

Other materials about Toyota Venza:

Power Window Motor Malfunction (B2311)
DESCRIPTION The power window regulator motor is operated by the power window regulator master switch assembly or power window regulator switch assembly. The power window regulator motor assembly has motor, regulator and ECU functions. This DTC is output ...

Internal Control Module EEPROM Error (P062F)
DESCRIPTION The ECM monitors its internal operation and it stores this DTC when it detects an internal malfunction. DTC No. DTC Detection Condition Trouble Area P062F An ECM internal error (EEPRO ...

Inspection
INSPECTION PROCEDURE 1. INSPECT UNIVERSAL JOINT SPIDER ASSEMBLY (a) Check the spider bearing axial play by turning the flange while holding the shaft tightly. HINT: If necessary, replace the propeller with center bearing shaft assembly. ...

© 2016-2024 Copyright www.tovenza.com

0.1267