Toyota Venza: Rear Height Control Sensor (B241A)

Toyota Venza Service Manual / Lighting (ext) / Lighting System / Rear Height Control Sensor (B241A)

DESCRIPTION

The headlight leveling ECU assembly receives signals indicating the height of the vehicle from the rear height control sensor sub-assembly RH.

DTC No.	DTC Detecting Condition	Trouble Area
B241A	Malfunction in rear height control sensor sub-assembly RH Open or short in rear height control sensor sub-assembly RH circuit	Rear height control sensor sub-assembly RH Harness or connector Headlight leveling ECU assembly

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

If either of the following is performed, initialization of the headlight leveling ECU assembly is necessary (See page ).

Replacement of the headlight leveling ECU assembly.
Replacement or removal/installation of the rear height control sensor sub-assembly or work that changes the vehicle height such as replacement of suspension components.

PROCEDURE

1.	CHECK FOR DTC

(a) Clear the DTCs (See page ).

(b) Check for DTCs (See page ).

OK:

DTC B241A is not output.

USE SIMULATION METHOD TO CHECK

2.	READ VALUE USING TECHSTREAM

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(d) Enter the following menus: Body Electrical / HL Auto Leveling / Data List.

(e) Read the display on the Techstream.

HL Auto Leveling

Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
Height Sens Pw Supply Val	Rear height control sensor power supply value / 0.00 to 5.00 V	Approx. 5 V	-
Rr Height Sens Signal Val	Rear height control sensor signal value / 0.00 to 5.00 V	Approx. 2.5 V (When the vehicle is level)	Value changes according to vehicle height

OK:

Normal conditions listed above are displayed.

REPLACE HEADLIGHT LEVELING ECU ASSEMBLY

3.	INSPECT REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY RH

(a) Remove the rear height control sensor sub-assembly RH (See page ).

(b) Inspect the rear height control sensor sub-assembly RH (See page ).

REPLACE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY RH

4.	CHECK HARNESS AND CONNECTOR (HEADLIGHT LEVELING ECU ASSEMBLY - REAR HEIGHT CONTROL SENSOR RH)

(a) Disconnect the A40 headlight leveling ECU assembly connector.

(b) Disconnect the N1 rear height control sensor sub-assembly RH connector.

Standard Resistance:

Tester Connection	Condition	Specified Condition
A40-19 (SHRL) - N1-2 (SHRR)	Always	Below 1 Ω
A40-19 (SHRL) - Body ground	Always	10 kΩ or higher

REPLACE HEADLIGHT LEVELING ECU ASSEMBLY

REPAIR OR REPLACE HARNESS OR CONNECTOR

HL AutoLeveling ECU Failure (B2420)

DESCRIPTION When the headlight leveling ECU assembly detects a malfunction in itself, this DTC is stored. DTC No. DTC Detecting Condition Trouble Area ...

Height Control Sensor Malfunction (B2416)

DESCRIPTION The DTC is stored when the headlight leveling ECU assembly detects malfunctions in the rear height control sensor sub-assembly RH power source or rear height control sensor sub-assemb ...

Other materials about Toyota Venza:

Removal
REMOVAL CAUTION / NOTICE / HINT NOTICE: Do not remove the steering angle sensor from the spiral cable. HINT: The steering angle sensor is a component of the spiral with sensor cable sub-assembly. If the steering angle sensor malfunctions, replace the sp ...

Noise Occurs
PROCEDURE 1. NOISE CONDITION (a) Check from which direction the noise comes (front left or right, or rear left or right). OK: The location of the noise source can be determined. NG GO TO STEP 3 ...

CD cannot be Ejected
PROCEDURE 1. CHECK OPERATION (a) Press the CD eject switch of the navigation receiver assembly for 10 seconds or more and check that the CD is ejected. OK: CD is ejected. NG REPLACE NAVIGATION RECEIVER ...