PROCEDURE
1. |
CHECK NAVIGATION RECEIVER ASSEMBLY |
(a) Check the radio automatic station search function.
(1) Check the radio automatic station search function by activating it.
Result |
Proceed to |
---|---|
Automatic station search function does not stop. |
A |
Automatic station search function stops on a station. |
B |
B |
REPLACE NAVIGATION RECEIVER ASSEMBLY |
|
2. |
CHECK OPTIONAL COMPONENTS |
(a) Check if any optional components that may decrease reception capacity, such as sunshade film or a telephone antenna, are installed.
Result |
Proceed to |
---|---|
Optional components are not installed. |
A |
Optional components are installed. |
B |
NOTICE:
Do not remove optional components without the permission of the customer.
B |
REMOVE OPTIONAL COMPONENTS AND CHECK AGAIN (SEE NOTICE ABOVE) |
|
3. |
CHECK RADIO ANTENNA |
(a) Preparation for check
(1) Remove the roof antenna pole sub-assembly (See page ).
(b) Check for noise
(1) Turn the ignition switch to ACC with the navigation receiver assembly connector connected.
(2) Turn the radio on and tune into AM mode.
(3) Place a screwdriver, thin wire or other metal object on the satellite radio antenna assembly threaded installation portion for the roof antenna pole sub-assembly and check that noise can be heard from the speakers (w/ SDARS System).
(4) Place a screwdriver, thin wire or other metal object on the No. 1 amplifier antenna assembly threaded installation portion for the roof antenna pole sub-assembly and check that noise can be heard from the speakers (w/o SDARS System).
Result |
Proceed to |
---|---|
Noise does not occur. |
A |
Noise occurs. |
B |
B |
REPLACE NAVIGATION RECEIVER ASSEMBLY |
|
4. |
CHECK NAVIGATION RECEIVER ASSEMBLY |
(a) Preparation for check (1) Remove the antenna connector from the navigation receiver assembly. |
|
(b) Check for noise
(1) Turn the ignition switch to ACC with the navigation receiver assembly connector connected.
(2) Turn the radio on and tune into AM mode.
(3) Place a screwdriver, thin wire or other metal object on the navigation receiver assembly antenna jack and check that noise can be heard from the speakers.
OK:
Noise can be heard from the speakers.
NG |
REPLACE NAVIGATION RECEIVER ASSEMBLY |
|
5. |
INSPECT NAVIGATION RECEIVER ASSEMBLY |
(a) Disconnect the RA navigation receiver assembly connector.
(b) Measure the voltage according to the value(s) in the table below. Standard Voltage:
|
|
NG |
REPLACE NAVIGATION RECEIVER ASSEMBLY |
|
6. |
REPLACE ANTENNA CORD SUB-ASSEMBLY |
(a) Replace the antenna cord sub-assembly with a new or known good one and check if radio broadcasts can be received normally (See page ).
OK:
Radio broadcasts can be received normally.
OK |
END |
|
7. |
REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY |
(a) Replace the No. 2 antenna cord sub-assembly with a new or known good one and check if radio broadcasts can be received normally (See page ).
OK:
Radio broadcasts can be received normally.
OK |
END |
|
8. |
REPLACE NO. 3 ANTENNA CORD SUB-ASSEMBLY |
(a) Replace the No. 3 antenna cord sub-assembly with a new or known good one and check if radio broadcasts can be received normally (See page ).
OK:
Radio broadcasts can be received normally.
OK |
END |
|
9. |
REPLACE ROOF ANTENNA POLE SUB-ASSEMBLY |
(a) Replace that the roof antenna pole sub-assembly with a new or known good one and check if radio broadcasts can be received normally (See page ).
OK:
Radio broadcasts can be received normally.
(b) Proceed to the next step based on the inspection result.
Condition |
Proceed to |
---|---|
NG |
A |
OK (w/o SDARS System) |
B |
OK (w/ SDARS System) |
C |
A |
CHECK AND REPLACE ROOF ANTENNA POLE SUB-ASSEMBLY |
C |
GO TO STEP 11 |
|
10. |
REPLACE NO. 1 AMPLIFIER ANTENNA ASSEMBLY |
(a) Replace the No. 1 amplifier antenna assembly with a new or known good one and check if radio broadcasts can be received normally (See page ).
OK:
Radio broadcasts can be received normally.
OK |
END |
NG |
REPLACE NAVIGATION RECEIVER ASSEMBLY |
11. |
REPLACE SATELLITE RADIO ANTENNA ASSEMBLY |
(a) Replace the satellite radio antenna assembly with a new or known good one and check if radio broadcasts can be received normally (See page ).
OK:
Radio broadcasts can be received normally.
OK |
END |
NG |
REPLACE NAVIGATION RECEIVER ASSEMBLY |
Operation Check
OPERATION CHECK
1. CHECK PANEL & STEERING SWITCH
HINT:
The radio and display receiver assembly panel switches and steering
switches are checked in the following procedure.
Illustrations may differ from the actual vehicle screen depending ...
Disassembly
DISASSEMBLY
PROCEDURE
1. INSPECT FRONT OIL PUMP AND GEAR BODY SUB-ASSEMBLY
2. REMOVE STATOR SHAFT ASSEMBLY
(a) Using a "TORX" wrench (T30), remove the 16 bolts and stator shaft
assembly from the oil pump body.
NOTICE:
Keep ...
Theft Deterrent System Communication Line High Fixation (B279A)
DESCRIPTION
If the communication line (EFIO - IMI) to the certification ECU (smart key ECU
assembly) is stuck high output (e.g. shorted to +B), the ECM stores this DTC.
DTC No.
DTC Detection Condition
Trouble Area
...