Toyota Venza: Problem Symptoms Table
PROBLEM SYMPTOMS TABLE
HINT:
- Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of probability in the "Suspected Area" column of the table. Check each symptom by checking the suspected areas in the order they are listed. Replace parts as necessary.
- Inspect the fuses and relays related to this system before inspecting the suspected areas below.
|
Symptom |
Suspected Area |
See page |
|---|---|---|
|
Steering is heavy. |
Front tires (Improperly inflated, unevenly worn) |
|
|
Front wheel alignment (Incorrect) |
|
|
|
Front suspension (Lower ball joint) |
|
|
|
Power steering gear (for 2GR-FE) |
|
|
|
Power steering gear (for 1AR-FE) |
|
|
|
Steering column assembly |
|
|
|
Torque sensor (Built into steering column assembly) |
- |
|
|
Power steering motor |
- |
|
|
Speed sensor |
|
|
|
Skid control ECU (Built into brake actuator) |
- |
|
|
Battery and power source system |
- |
|
|
Power steering ECU power source voltage and relay |
- |
|
|
Power steering ECU assembly |
|
|
|
Poor return |
Front tires (Improperly inflated, unevenly worn) |
|
|
Front wheel alignment (Incorrect) |
|
|
|
Steering column assembly |
|
|
|
Power steering ECU assembly |
|
|
|
Excessive free play |
Front tires (Improperly inflated, unevenly worn) |
|
|
Front suspension (Lower ball joint) |
|
|
|
Intermediate shaft, universal joint, sliding yoke (Worn) |
- |
|
|
Front wheel bearing (Worn) |
|
|
|
Steering effort differs between right and left or is uneven. |
Rotation angle sensor initialization and torque sensor zero point calibration |
|
|
Front tires (Improperly inflated, unevenly worn) |
|
|
|
Front wheel alignment (Incorrect) |
|
|
|
Front suspension (Lower ball joint) |
|
|
|
Power steering gear (for 2GR-FE) |
|
|
|
Power steering gear (for 1AR-FE) |
|
|
|
Torque sensor (Built into steering column assembly) |
- |
|
|
Steering column assembly |
|
|
|
Power steering motor |
- |
|
|
Power steering ECU assembly |
|
|
|
While driving, steering effort does not change in accordance with vehicle speed or the steering wheel does not return properly. |
Front suspension (Lower ball joint) |
|
|
Speed sensor |
|
|
|
Skid control ECU (Built into brake actuator) |
- |
|
|
Combination meter |
|
|
|
Torque sensor (Built into steering column assembly) |
- |
|
|
Power steering motor |
- |
|
|
Power steering gear (for 2GR-FE) |
|
|
|
Power steering gear (for 1AR-FE) |
|
|
|
Power steering ECU assembly |
|
|
|
A knocking (or cranking) sound occurs when turning the steering wheel while power steering is operating. |
Front suspension (Lower ball joint) |
|
|
Steering intermediate shaft |
- |
|
|
Power steering gear (for 2GR-FE) |
|
|
|
Power steering gear (for 1AR-FE) |
|
|
|
Noise occurs when turning the steering wheel during low speed driving. |
Power steering gear (for 2GR-FE) |
|
|
Power steering gear (for 1AR-FE) |
|
|
|
Steering column assembly |
|
|
|
Power steering ECU assembly |
|
|
|
High-pitched sounds (squeaking) occur when turning the steering wheel slowly with the vehicle stopped. |
Power steering gear (for 2GR-FE) |
|
|
Power steering gear (for 1AR-FE) |
|
|
|
Power steering motor |
- |
|
|
The steering wheel vibrates and noise occurs when turning the steering wheel from lock to lock. |
Power steering gear (for 2GR-FE) |
|
|
Power steering gear (for 1AR-FE) |
|
|
|
Steering column assembly |
|
|
|
PS warning light remains on. |
Proceed to PS warning light remains on |
|
.gif)
Precaution
PRECAUTION
1. IGNITION SWITCH EXPRESSIONS
HINT:
The type of ignition switch used on this model differs according to the specifications
of the vehicle. The expressions listed in the table below ar ...
Adjustment
ADJUSTMENT
PROCEDURE
1. ADJUST STEERING WHEEL OFF CENTER
(a) Inspect steering wheel off center.
(1) Apply masking tape on the top center of the steering wheel and steering
column up ...
Other materials about Toyota Venza:
Internal Control Module Monitoring Processor Performance (P060A)
MONITOR DESCRIPTION
The main CPU and sub CPU of the ECM perform data communication between each other.
The main CPU monitors the communications and WDC pulses from the sub CPU. When the
signal malfunctions below are detected, the DTC is output.
...
How To Proceed With Troubleshooting
CAUTION / NOTICE / HINT
HINT:
Use these procedure to troubleshoot the sliding roof system.
*: Use the Techstream.
PROCEDURE
1.
VEHICLE BROUGHT TO WORKSHOP
NEXT
...
Door Courtesy Switch Circuit
DESCRIPTION
The main body ECU (driver side junction block assembly) detects the condition
of the door courtesy light switch.
WIRING DIAGRAM
PROCEDURE
1.
READ VALUE USING TECHSTREAM
(a) Connect the Techstream to the DLC3 ...
0.131