Toyota Venza: Pressure Control Solenoid "C" Electrical (Shift Solenoid Valve SL3) (P0798)

Toyota Venza Service Manual / U660e Automatic Transmission / Transaxle / Automatic Transaxle System / Pressure Control Solenoid "C" Electrical (Shift Solenoid Valve SL3) (P0798)

DESCRIPTION

Changing from 1st to 6th is performed by the TCM turning shift solenoid valves SL1, SL2, SL3, SL4 and SL on and off. If an open or short circuit occurs in any of the shift solenoid valves, the TCM controls the remaining normal shift solenoid valves to allow the vehicle to be operated (See page ).

DTC No.	DTC Detection Condition	Trouble Area
P0798	The TCM checks for an open or short in the shift solenoid valve SL3 circuit while driving and shifting gears. (1-trip detection logic) Output signal duty equals to 100%. (NOTE: SL3 output signal duty is less than 100% under normal condition.)	Open or short in shift solenoid valve SL3 circuit Shift solenoid valve SL3 TCM

MONITOR DESCRIPTION

The TCM commands gear shifts by turning the shift solenoid valves on or off. When there is an open or short circuit in any shift solenoid valve circuit, the TCM detects the problem and illuminates the MIL and stores the DTC. And the TCM performs the fail-safe function and turns the other normal shift solenoid valves on or off (In case of an open or short circuit, the TCM stops sending current to the circuit.)

(See page ).

MONITOR STRATEGY

Related DTCs	P0798: Shift solenoid valve SL3/Range check
Required sensors/Components	Shift solenoid valve SL3
Frequency of operation	Continuous
Duration	1 sec.
MIL operation	Immediate
Sequence of operation	None

TYPICAL ENABLING CONDITIONS

All

The monitor will run whenever the following DTCs are not present	None
Ignition switch	ON
Starter	OFF

Condition (A)

Battery voltage

12 V or more

Condition (B)

Battery voltage	10 V or more and less than 12 V
Target current	Less than 0.75 A

Condition (C)

Battery voltage	8 V or more
Target current	0.25 A or more

TYPICAL MALFUNCTION THRESHOLDS

Condition (A) and (B)

Output duty cycle

100% or more

Condition (C)

Output duty cycle

0% or less

COMPONENT OPERATING RANGE

Output duty cycle

More than 3% and less than 100%

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Perform the universal trip to clear permanent DTCs (See page ).

PROCEDURE

1.	INSPECT TRANSMISSION WIRE (SL3)

(a) Remove the TCM from the transaxle.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection	Condition	Specified Condition
16 (SL3+) - 15 (SL3-)	20°C (68°F)	5.0 to 5.6 Ω
16 (SL3+) - Body ground	Always	10 kΩ or higher
15 (SL3-) - Body ground	Always	10 kΩ or higher
16 (SL3+) - All other terminals except 15 (SL3-)	Always	10 kΩ or higher
15 (SL3-) - All other terminals except 16 (SL3+)	Always	10 kΩ or higher

REPLACE TCM

2.	INSPECT SHIFT SOLENOID VALVE SL3

(a) Remove shift solenoid valve SL3.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection	Condition	Specified Condition
1 - 2	20°C (68°F)	5.0 to 5.6 Ω

Text in Illustration

*1	Shift Solenoid Valve SL3

(c) Connect a battery positive (+) lead with a 21 W bulb to terminal 2 and a negative (-) lead to terminal 1 of the solenoid valve connector. Then check that the valve moves and makes an operating sound.

OK:

Valve moves and makes an operating sound.

REPLACE TRANSMISSION WIRE

REPLACE SHIFT SOLENOID VALVE SL3

Pressure Control Solenoid "D" Performance (Shift Solenoid Valve SLT) (P2714)

SYSTEM DESCRIPTION The linear solenoid valve (SLT) controls the transmission line pressure for smooth transmission operation based on signals from the throttle position sensor and the vehicle spe ...

Transmission Fluid Pressure Sensor / Switch "E" Circuit Low (P0989,P0990)

DESCRIPTION ATF pressure switch No. 3 is installed in the lock-up solenoid ATF output passage and is used to detect a malfunction in the lock-up solenoid. DTC No. DTC Detecti ...

Other materials about Toyota Venza:

Antenna Coil Open / Short (B2784)
DESCRIPTION This DTC is stored when there is an open or short in the transponder key coil (built into the engine switch). DTC No. DTC Detection Condition Trouble Area B2784 Transponder key coil i ...

Door Mirror Foot Light Circuit
DESCRIPTION The main body ECU (driver side junction block assembly) controls the door mirror foot lights. WIRING DIAGRAM 1. w/o Seat Position Memory: 2. w/ Seat Position Memory: PROCEDURE 1. CHECK VEHICLE CONDITION ...

Problem Symptoms Table
PROBLEM SYMPTOMS TABLE HINT: Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of probability in the "Suspected Area" column of ...