Toyota Venza: Precaution
PRECAUTION
1. PRECAUTION FOR DISCONNECTING THE BATTERY CABLE
NOTICE:
When disconnecting the cable from the negative (-) battery terminal, initialize the following systems after the cable is reconnected:
|
System |
See Procedure |
|---|---|
|
Back Door Closer System |
|
|
Power Back Door System |
|
2. EXPRESSIONS OF IGNITION SWITCH
The type of ignition switch used on this model differs according to the specifications of the vehicle.
The expressions listed in the table below are used in this section.
|
Expression |
Switch Type |
|
|---|---|---|
|
Ignition Switch (Position) |
Engine Switch (Condition) |
|
|
Ignition switch off |
LOCK |
off |
|
Ignition switch ON |
ON |
on (IG) |
|
Ignition switch ACC |
ACC |
on (ACC) |
|
Engine start |
START |
start |
3. HANDLING PRECAUTIONS FOR SRS AIRBAG SYSTEM
(a) The vehicle is equipped with a Supplemental Restraint System (SRS). Failure to carry out service operations in the correct sequence could cause the SRS to unexpectedly deploy during servicing. This may cause a serious accident.
Before servicing (including inspection, replacement, removal and installation
of parts), be sure to read the precautionary notices for the Supplemental Restraint
System (See page .gif)
).
4. PRECAUTIONS FOR REMOVAL, INSTALLATION AND REPLACEMENT OF ELECTRONIC MOTOR POWER STEERING COMPONENTS
(a) After replacing the power steering ECU assembly, clear the rotation angle
sensor calibration value, initialize the rotation angle sensor, and calibrate the
torque sensor zero point (See page ).
5. HANDLING PRECAUTION
(a) When handling the electronic parts:
- Avoid any impact to electronic parts such as ECUs and relays. Replace them with new ones if dropped or subjected to a severe blow.
- Do not expose any electronic parts to high temperatures or humidity.
- In order to prevent deformation or malfunctions due to static electricity, do not touch the connector terminals.
(b) Before disconnecting the connectors related to the electronic power steering system, turn the ignition switch to ON, center the steering wheel and then turn the ignition switch off.
6. PRECAUTIONS FOR CAN COMMUNICATION
(a) CAN communication lines are used to receive information from the skid control ECU and the ECM, and to transmit warnings to the combination meter.
When there are any problems in the CAN communication lines, DTCs of the CAN communication line are output.
(b) Perform troubleshooting for the communication line problems when DTCs of the CAN communication are output. Be sure to start troubleshooting on the power steering system after confirming that the CAN communication system is normal.
(c) Since the CAN communication line has its own length and route, it cannot be repaired temporarily with a bypass wire, etc.
Parts Location
PARTS LOCATION
ILLUSTRATION
ILLUSTRATION
...
System Diagram
SYSTEM DIAGRAM
Transmitting ECU
(Transmitter)
Receiving ECU
Signal
Communication Method
ECM
Power Steering ECU
...
Other materials about Toyota Venza:
Dtc Check / Clear
DTC CHECK / CLEAR
1. CHECK DTC
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG).
(c) Read the DTC by following the prompts on the Techstream screen.
HINT:
Refer to the Techstream operator's manual for further details.
2. CL ...
Installation
INSTALLATION
PROCEDURE
1. INSTALL VACUUM SWITCHING VALVE ASSEMBLY (for ACIS)
(a) Install the vacuum switching valve assembly (for ACIS) with the bolt.
Torque:
9.0 N·m {92 kgf·cm, 80 in·lbf}
...
Diagnosis System
DIAGNOSIS SYSTEM
1. DESCRIPTION
The ECM controls the cruise control system of the vehicle. The data and DTCs
relating to the cruise control system can be read from the DLC3 of the vehicle.
If either DTC or CRUISE OK is not displayed on the multi-informat ...
0.1746