Toyota Venza manuals

Toyota Venza: Power Steering ECU Communication Stop Mode

Toyota Venza Service Manual / Networking / Can Communication System / Power Steering ECU Communication Stop Mode

DESCRIPTION

Detection Item

Symptom

Trouble Area

Power Steering ECU Communication Stop Mode

  • "EPS" is not displayed on "CAN Bus Check" screen of the Techstream.
  • Applies to Power Steering ECU Communication Stop Mode in DTC Combination Table.
  • Power source circuit of power steering ECU
  • Power steering ECU branch wire or connector
  • Power steering ECU

WIRING DIAGRAM


CAUTION / NOTICE / HINT

NOTICE:

  • Turn the ignition switch off before measuring the resistances between CAN bus main wires and between CAN bus branch wires.
  • Turn the ignition switch off before inspecting CAN bus wires for a ground short.
  • After the ignition switch is turned off, check that the key reminder warning system and light reminder warning system are not operating.
  • Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If any doors need to be opened in order to check connectors, open the doors and leave them open.

HINT:

  • Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
  • Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

PROCEDURE

1.

CHECK CAN BUS WIRE FOR DISCONNECTION (POWER STEERING ECU BRANCH WIRE)

(a) Turn the ignition switch off.

(b) Disconnect the connector of the power steering ECU.

Text in Illustration

*1

Front view of wire harness connector

(to Power Steering ECU)


(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Switch Condition

Specified Condition

D20-1 (CANH) - D20-7 (CANL)

Ignition switch off

54 to 69 Ω


NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (POWER STEERING ECU BRANCH WIRE)


OK

2.

CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)

(a) Turn the ignition switch to ON.

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Switch Condition

Specified Condition

D20-6 (IG) - Body ground

Ignition switch ON

11 to 14 V

Text in Illustration

*1

Front view of wire harness connector

(to Power Steering ECU)



NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)


OK

3.

CHECK HARNESS AND CONNECTOR (GROUND TERMINAL)

(a) Turn the ignition switch off.

(b) Disconnect the connector of the power steering ECU.

Text in Illustration

*1

Front view of wire harness connector

(to Power Steering ECU)


(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

D19-2 (PGND) - Body ground

Always

Below 1 Ω


OK

REPLACE POWER STEERING ECU


NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GROUND CIRCUIT)

Skid Control ECU Communication Stop Mode
DESCRIPTION Detection Item Symptom Trouble Area Skid Control ECU Communication Stop Mode "ABS/VSC/TRAC" is not displa ...

Steering Angle Sensor Communication Stop Mode
DESCRIPTION Detection Item Symptom Trouble Area Steering Angle Sensor Communication Stop Mode "Steering Angle Sensor" ...

Other materials about Toyota Venza:

Inspection
INSPECTION PROCEDURE 1. INSPECT PRELOAD (a) Secure the steering column assembly in a vise. Text in Illustration *1 Service Nut *2 Steering Wheel Assembly Set Nut ...

Radiator Grille
Components COMPONENTS ILLUSTRATION Removal REMOVAL PROCEDURE 1. REMOVE COOL AIR INTAKE DUCT SEAL 2. REMOVE RADIATOR GRILLE (a) Put protective tape around the radiator grille. Text in Illustration *1 ...

Transmission Fluid Pressure Sensor / Switch "E" Circuit Low (P0989,P0990)
DESCRIPTION ATF pressure switch No. 3 is installed in the lock-up solenoid ATF output passage and is used to detect a malfunction in the lock-up solenoid. DTC No. DTC Detection Condition Trouble Area P0989 ...

© 2016-2024 Copyright www.tovenza.com

0.1178