Toyota Venza: Power Management Control ECU Communication Stop Mode

Toyota Venza Service Manual / Networking / Can Communication System / Power Management Control ECU Communication Stop Mode

DESCRIPTION

Detection Item	Symptom	Trouble Area
Power Management Control ECU Communication Stop Mode	"Electric Power Control" is not displayed on the CAN Bus Check screen of Techstream. Applies to "Power Management Control ECU Communication Stop Mode" in the DTC Combination Table.	Power source circuit of power management control ECU Power management control ECU branch wire or connector Power management control ECU

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Turn the ignition switch off before measuring the resistances between CAN bus main wires and between CAN bus branch wires.
Turn the ignition switch off before inspecting CAN bus wires for a ground short.
After the ignition switch is turned off, check that the key reminder warning system and light reminder warning system are not operating.
Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If any doors need to be opened in order to check connectors, open the doors and leave them open.

HINT:

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

PROCEDURE

1.	CHECK OPEN IN CAN NO. 1 BUS WIRE (POWER MANAGEMENT CONTROL ECU BRANCH WIRE)

(a) Turn the ignition switch off.

(b) Disconnect the power management control ECU connector (D43).

Text in Illustration

*1	Rear view of wire harness connector (to Power Management Control ECU)

Standard Resistance:

Tester Connection	Condition	Specified Value
D43-14 (CA1H) - D43-13 (CA1L)	Ignition switch off	54 to 69 Ω

REPAIR OR REPLACE CAN NO. 1 BUS BRANCH WIRE OR CONNECTOR (POWER MANAGEMENT CONTROL ECU)

2.	CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)

(a) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection	Condition	Specified Value
D43-1 (AM22) - Body Ground	Always	11 to 14 V
D43-2 (AM21) - Body Ground	Always	11 to 14 V

Text in Illustration

*1	Rear view of wire harness connector (to Power Management Control ECU)

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE TERMINAL)

3.	CHECK HARNESS AND CONNECTOR (GROUND TERMINAL)

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection	Condition	Specified Value
D43-6 (GND) - Body Ground	Always	Below 1 Ω

Text in Illustration

*1	Rear view of wire harness connector (to Power Management Control ECU)

REPLACE POWER MANAGEMENT CONTROL ECU

REPAIR OR REPLACE HARNESS OR CONNECTOR (GROUND TERMINAL)

Main Body ECU Communication Stop Mode

DESCRIPTION Detection Item Symptom Trouble Area Main Body ECU Communication Stop Mode "Main Body" is not displayed on ...

Certification ECU Communication Stop Mode

DESCRIPTION Detection Item Symptom Trouble Area Certification ECU Communication Stop Mode "Smart Access/Smart Key/Wireless ...

Other materials about Toyota Venza:

Reassembly
REASSEMBLY PROCEDURE 1. INSTALL FRONT OIL PUMP OIL SEAL (a) Using SST and a hammer, install a new oil seal to the oil pump body. SST: 09350-32014 09351-32140 Oil seal driven in depth: -0.25 to 0.25 mm (-0.00984 to 0.00984 in.) ...

Power Steering ECU Communication Stop Mode
DESCRIPTION Detection Item Symptom Trouble Area Power Steering ECU Communication Stop Mode "EPS" is not displayed on "CAN Bus Check" screen of the Techstream. ...

Short to GND in Immobiliser System Power Source Circuit (B278A)
DESCRIPTION This DTC is stored when the engine switch power source supply line is open or shorted. DTC No. DTC Detection Condition Trouble Area B278A Engine switch power source supply line is ope ...