DESCRIPTION
This circuit consists of the occupant classification ECU and power source circuit (battery, fuse and wire harness).
DTC B1794 is recorded when a malfunction is detected in the occupant classification ECU or power source circuit.
HINT:
If DTC B1794 is output after turning the ignition switch from off to ON and to off 50 times in a row when a malfunction occurs in the power circuit for the occupant classification system.
This DTC is output if a malfunction is detected even after being cleared unless the normal system code is input.
DTC No. |
DTC Detection Condition |
Trouble Area |
---|---|---|
B1794 |
|
|
When DTC B1650/32 is detected as a result of troubleshooting for the airbag system, check the DTCs stored in the occupant classification ECU. When DTC B1794 is output, perform troubleshooting for the DTC.
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
PROCEDURE
1. |
CHECK BATTERY |
(a) Measure the voltage of the battery.
Standard Voltage:
11 to 14 V
NG |
REPLACE BATTERY |
|
2. |
CHECK WIRE HARNESS (SOURCE VOLTAGE) |
(a) Turn the ignition switch off. |
|
(b) Disconnect the cable from the negative (-) battery terminal.
(c) Disconnect the connector from the occupant classification ECU.
(d) Connect the cable to the negative (-) battery terminal.
(e) Turn the ignition switch to ON.
(f) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
for Power Seat
Tester Connection |
Condition |
Specified Condition |
---|---|---|
S12-1 (+B) - Body ground |
Always |
11 to 14 V |
S12-7 (IG) - Body ground |
Ignition switch ON |
11 to 14 V |
for Manual Seat
Tester Connection |
Condition |
Specified Condition |
---|---|---|
M14-1 (+B) - Body ground |
Always |
11 to 14 V |
M14-7 (IG) - Body ground |
Ignition switch ON |
11 to 14 V |
(g) Turn the ignition switch off.
(h) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
for Power Seat
Tester Connection |
Condition |
Specified Condition |
---|---|---|
S12-3 (GND) - Body ground |
Always |
Below 1 Ω |
for Manual Seat
Tester Connection |
Condition |
Specified Condition |
---|---|---|
M14-3 (GND) - Body ground |
Always |
Below 1 Ω |
*1 |
for Power Seat |
*2 |
for Manual Seat |
*3 |
Front view of wire harness connector (to Occupant Classification ECU) |
NG |
REPLACE WIRE HARNESS |
|
3. |
CHECK DTC |
(a) Turn the ignition switch off.
(b) Disconnect the cable from the negative (-) battery terminal.
(c) Connect the connector to the occupant classification ECU.
(d) Connect the Techstream to the DLC3.
(e) Connect the cable to the negative (-) battery terminal.
(f) Turn the ignition switch to ON.
(g) Clear the DTCs stored in the occupant classification ECU (See page ).
(h) Clear the DTCs stored in the center airbag sensor assembly (See page ).
(i) Turn the ignition switch off.
(j) Turn the ignition switch to ON, and wait for at least 10 seconds.
(k) Using the Techstream, check for DTCs of the occupant classification ECU (See page ).
OK:
DTC B1794 is not output.
HINT:
Codes other than DTC B1794 may be output at this time, but they are not related to this check.
OK |
USE SIMULATION METHOD TO CHECK |
|
4. |
REPLACE OCCUPANT CLASSIFICATION ECU |
(a) Turn the ignition switch off.
(b) Disconnect the cable from the negative (-) battery terminal.
(c) Replace the occupant classification ECU (See page ).
|
5. |
PERFORM ZERO POINT CALIBRATION |
(a) Connect the cable to the negative (-) battery terminal.
(b) Connect the Techstream to the DLC3.
(c) Turn the ignition switch to ON.
(d) Using the Techstream, perform Zero Point Calibration (See page ).
OK:
"Zero Point Calibration is complete." is displayed.
|
6. |
PERFORM SENSITIVITY CHECK |
(a) Using the Techstream, perform Sensitivity Check (See page ).
Standard:
27 to 33 kg (59.5 to 72.8 lb)
NEXT |
END |
Road Test
ROAD TEST
1. PROBLEM SYMPTOM CONFIRMATION
(a) Inspect the SET function.
Text in Illustration
*1
ON/OFF
*2
- SET
(1) Turn the cruise control main switch on.
(2) Drive at the required speed of bet ...
Removal
REMOVAL
PROCEDURE
1. PRECAUTION
(See page )
2. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD
3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-)
battery terminal to disab ...
On-vehicle Inspection
ON-VEHICLE INSPECTION
PROCEDURE
1. INSPECT DISCHARGE HEADLIGHT BULB
NOTICE:
Confirm the following items before replacing a discharge headlight bulb. If a
malfunction is discovered and repaired, perform the inspection again to confirm
the repair.
...