Toyota Venza: On-vehicle Inspection

Toyota Venza Service Manual / Lighting (ext) / High Intensity Discharge Headlight Bulb / On-vehicle Inspection

ON-VEHICLE INSPECTION

PROCEDURE

1. INSPECT DISCHARGE HEADLIGHT BULB

NOTICE:

Confirm the following items before replacing a discharge headlight bulb. If a malfunction is discovered and repaired, perform the inspection again to confirm the repair.

Make sure that the high voltage socket of the light control ECU and discharge headlight bulb are connected normally.
Make sure that there is no damage to the high voltage socket of the light control ECU or discharge headlight bulb connector.

HINT:

Even if a bulb seems to turn on normally, it may not be normal. Perform all the following steps in order because an abnormal condition might otherwise not be easy to duplicate.

(a) Prepare the vehicle:

Before performing the following inspection procedure, turn off the discharge headlight bulbs for more than 10 minutes to allow them to cool down sufficiently.

HINT:

Since it is necessary to find the cause of a malfunction that causes a discharge headlight bulb not to turn on, the discharge headlight bulbs should be inspected starting from a cooled off state.

(1) Turn on the discharge headlights for more than 25 minutes, and check that the bulbs illuminate normally when they are turned on.

HINT:

Leave the headlights on for more than 25 minutes to stabilize the discharge headlight bulb arc tube voltage.
A discharge headlight bulb that has almost reached the end of its life may turn off due to a headlight control ECU fail-safe function because the arc tube voltage is high.

(2) Repeatedly turn the discharge headlights off for 15 seconds and on for 15 seconds (5 times for each). Check that the bulbs illuminate normally.

HINT:

This inspection confirms the ability of the bulbs to start when hot.

(3) Turn off the discharge headlights for 3 minutes, and then turn on the discharge headlights for 3 minutes. Check that the bulbs illuminate normally when they are turned on.

HINT:

A characteristic of discharge headlight bulbs is that their starting voltage is highest when 3 minutes have elapsed after being turned off. This is the most difficult situation for discharge bulbs to start in.
This inspection is further confirmation of the ability of the bulbs to start when hot.

Standard:

The discharge headlight bulbs illuminate normally in all steps.

(4) Remove the discharge headlight bulb and perform a visual inspection of the arc tube.

Standard:

The inside of the arc tube is not bulging or deformed and is not clouded. However, a dull brown coloration inside the arc tube is normal.

Text in Illustration

*A	Discharge Headlight Bulb is Normal	*B	Discharge Headlight Bulb at End of Usable Life
*1	Arc Tube	-	-
	Inside of Arc Tube		Distortion / Clouded Area

Components

COMPONENTS ILLUSTRATION ILLUSTRATION ...

Installation

INSTALLATION PROCEDURE 1. INSTALL DISCHARGE HEADLIGHT BULB HINT: Use the same procedure for the RH side and LH side (See page ). 2. INSTALL LIGHT CONTROL ECU (for LH Side) (a) Turn ...

Other materials about Toyota Venza:

Removal
REMOVAL PROCEDURE 1. REMOVE AIR CONDITIONING UNIT ASSEMBLY (See page ) 2. REMOVE NO. 1 FINISH PANEL MOUNTING BRACKET 3. REMOVE NO. 2 FINISH PANEL MOUNTING BRACKET 4. REMOVE NO. 3 AIR DUCT SUB-ASSEMBLY 5. REMOVE NO. 2 AIR DUCT SUB-ASSEMBLY ...

Relay
On-vehicle Inspection ON-VEHICLE INSPECTION PROCEDURE 1. INSPECT DOME CUT RELAY (a) Measure the resistance according to the value(s) in the table below. Standard Resistance: Tester Connection Condition ...

Removal
REMOVAL CAUTION / NOTICE / HINT NOTICE: Release the vacuum from the booster by depressing the brake pedal several times. Then remove the brake master cylinder from the brake booster. PROCEDURE 1. DRAIN BRAKE FLUID NOTICE: If brake fluid leaks onto any ...