Toyota Venza: Navigation Receiver Assembly Communication Stop Mode

Toyota Venza Service Manual / Networking / Can Communication System / Navigation Receiver Assembly Communication Stop Mode

DESCRIPTION

Detection Item	Symptom	Trouble Area
Navigation Receiver Assembly Communication Stop Mode	"Display and Navigation (AVN1)" is not displayed on the "CAN Bus Check" screen of the Techstream Applies to Navigation Receiver Assembly Communication Stop Mode in DTC Combination Table.	Power source circuit of navigation receiver assembly Navigation receiver assembly branch wire or connector Navigation receiver assembly

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Turn the ignition switch off before measuring the resistances between CAN bus main wires and between CAN bus branch wires.
Turn the ignition switch off before inspecting CAN bus wires for a ground short.
After the ignition switch is turned off, check that the key reminder warning system and light reminder warning system are not operating.
Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If any doors need to be opened in order to check connectors, open the doors and leave them open.

HINT:

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

PROCEDURE

1.	CHECK FOR OPEN IN CAN BUS WIRES (NAVIGATION RECEIVER ASSEMBLY BRANCH WIRE)

(a) Turn the ignition switch off.

(b) Disconnect the navigation receiver assembly connector.

Text in Illustration

*1	Front view of wire harness connector (to Navigation Receiver Assembly)

Standard Resistance:

Tester Connection	Condition	Specified Condition
E40-9 (CANH) - E40-10 (CANL)	Ignition switch off	54 to 69 Ω

REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (NAVIGATION RECEIVER ASSEMBLY BRANCH WIRE)

2.	CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)

(a) Disconnect the navigation receiver assembly connector.

Text in Illustration

*1	Front view of wire harness connector (to Navigation Receiver Assembly)

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection	Condition	Specified Condition
E38-4 (+B1) - Body ground	Always	11 to 14 V
E38-3 (ACC1) - Body ground	Ignition switch ACC	11 to 14 V
E40-1 (IG) - Body ground	Ignition switch ON	11 to 14 V

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE TERMINAL)

3.	CHECK HARNESS AND CONNECTOR (GROUND TERMINAL)

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection	Condition	Specified Condition
E38-7 (GND1) - Body ground	Always	Below 1 Ω

Text in Illustration

*1	Front view of wire harness connector (to Navigation Receiver Assembly)

REPLACE NAVIGATION RECEIVER ASSEMBLY

REPAIR OR REPLACE HARNESS OR CONNECTOR (GROUND TERMINAL)

4WD Control ECU Communication Stop Mode

DESCRIPTION Detection Item Symptom Trouble Area 4WD Control ECU Communication Stop Mode "Four Wheel Drive Control" is ...

Audio Receiver Assembly Communication Stop Mode

DESCRIPTION Detection Item Symptom Trouble Area Audio Receiver Assembly Communication Stop Mode "Display and Navigation (A ...

Other materials about Toyota Venza:

Air conditioning filter
The air conditioning filter must be changed regularly to maintain air conditioning efficiency. - Removal method Vehicles with smart key system: Turn the “ENGINE START STOP” switch off. Vehicles without smart key system: Turn the engine switch ...

Front Airbag Sensor RH Malfunction (B1610/13)
DESCRIPTION The front airbag sensor RH circuit consists of the center airbag sensor assembly and front airbag sensor RH. The front airbag sensor RH detects impacts to the vehicle and sends signals to the center airbag sensor assembly to determine if the ...

Operation Check
OPERATION CHECK 1. CHECK AUTO OPERATION NOTICE: Make sure that initialization is completed before inspection (See page ). HINT: When pressing the switch for 0.3 seconds or less, the roof glass moves but auto operation does not operate. (a) Turn the i ...