Toyota Venza manuals

Toyota Venza: Moon roof

Use the overhead switches to open, close, and tilt the moon roof up and down.

 - Opening and closing


1. Open
The moon roof stops slightly before the fully open position to reduce wind noise. Move the switch backward again to fully open.

2. Close (push and hold) The moon roof stops once.

Push and hold the switch again to fully close.

 - Tilt up and down


1. Tilt up
2. Tilt down (push and hold)

 - The moon roof can be operated when

Vehicles with smart key system The “ENGINE START STOP” switch is in IGNITION ON mode.

Vehicles without smart key system The engine switch is in the “ON” position.

 - Operating the moon roof after turning the engine off Vehicles with smart key system The moon roof can be operated for approximately 45 seconds even after the “ENGINE START STOP” switch is turned to ACCESSORY mode or turned off. It cannot, however, be operated once either front door is opened.

Vehicles without smart key system The moon roof can be operated for approximately 45 seconds even after the engine switch is turned to the “ACC” or “LOCK” position. It cannot, however, be operated once either front door is opened.

 - To reduce moon roof wind noise

When the moon roof is opened automatically, it will stop slightly before the fully open position. Driving with the moon roof in this position can help reduce wind noise.

 - Sunshade

 - Open moon roof warning buzzer

Vehicles with smart key system The buzzer sounds and message is shown on the multi-information display (TFT type only) when the “ENGINE START STOP” switch is turned off and the driver’s door is opened with the moon roof open.

Vehicles without smart key system The buzzer sounds and message is shown on the multi-information display (TFT type only) when the engine switch is turned to the “LOCK” position and the driver’s door is opened with the moon roof open.

 - When the moon roof does not close normally

Perform the following procedure:

Stop the vehicle.


Open the moon roof halfway.


Press and hold the open/close switch
in the close position.

When the moon roof reaches the full close position, maintain the open/close switch in the close position for more than 2 seconds.

It will adjust slightly and then stop.

To ensure the initialization is complete,
make sure opening, closing, tilting up and down functions work properly.

If the moon roof does not fully close even after performing the above procedure correctly, have the vehicle inspected by your Toyota dealer.

CAUTION

 - Opening the moon roof

Observe the following precautions.

Failing to do so may cause death or serious injury.

• Do not allow any passengers to put their hands or heads outside the vehicle while it is moving.

• Do not sit on top of the moon roof.

 - Closing the moon roof

Observe the following precautions.

Failing to do so may result in death or serious injury.

• Check to make sure that all passengers do not have any part of their bodies in a position where they could be caught when the moon roof is being operated.

• Do not allow children to operate the moon roof.

Closing the moon roof on someone can cause death or serious injury.

Power windows
The power windows can be opened and closed using the following switches. 1. One-touch closing* 2. Closing 3. One-touch opening* 4. Opening *:To stop the window partway, operate the switch in th ...

Sunshade
The sunshade can be opened and closed manually. ► Front Slide the sunshade. The front sunshade will open automatically when the moon roof is opened. ► Rear Slide the sunshade. ...

Other materials about Toyota Venza:

Mass or Volume Air Flow Circuit Low Input (P0102,P0103)
DESCRIPTION The mass air flow meter is a sensor that measures the amount of air flowing through the throttle valve. The ECM uses this information to determine the fuel injection time and to provide the appropriate air-fuel ratio. Inside the mass air flow ...

Short in Passenger Side Airbag Variable Vent Hole Squib Circuit (B181A/7A-B181D/7A)
DESCRIPTION The passenger side airbag variable vent hole squib circuit consists of the center airbag sensor assembly and front passenger airbag assembly. The center airbag sensor assembly uses this circuit to deploy the airbag when deployment conditions ...

VC Output Circuit
DESCRIPTION The ECM constantly generates 5 V of power from battery voltage supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power to the sensors through the VC output circuit. When the VC circuit is short-cir ...

© 2016-2024 Copyright www.tovenza.com

0.1576