Toyota Venza: Lost Communication with "Seat Control Module A" (U0208)

Toyota Venza Service Manual / Networking / Can Communication System / Lost Communication with "Seat Control Module A" (U0208)

DESCRIPTION

DTC No.	DTC Detection Condition	Trouble Area
U0208	No communication from the position control ECU and switch assembly.	Position control ECU and switch assembly branch wire or connector Power source circuit of position control ECU and switch assembly Position control ECU and switch assembly

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Turn the ignition switch off before measuring the resistances between CAN bus main wires and between CAN bus branch wires.
Turn the ignition switch off before inspecting CAN bus wires for a ground short.
After the ignition switch is turned off, check that the key reminder warning system and light reminder warning system are not operating.
Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If any doors need to be opened in order to check connectors, open the doors and leave them open.

HINT:

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

PROCEDURE

1.	RECONFIRM DTC OUTPUT

(a) Reconfirm DTCs.

HINT:

If CAN MS bus DTC U1002 is output from the main body ECU (Techstream display: Main Body), troubleshoot for U1002 and check for malfunctions in the CAN MS bus circuit.

Result	Proceed to
U1002 is not output from main body ECU (Techstream display: Main Body)	A
U1002 is output from main body ECU (Techstream display: Main Body)	B

GO TO CIRCUITS INDICATED BY OUTPUT DTCS

2.	CHECK FOR OPEN IN CAN BUS WIRES (POSITION CONTROL ECU AND SWITCH ASSEMBLY BRANCH WIRE)

(a) Turn the ignition switch off.

(b) Disconnect the position control ECU and switch assembly connector.

Text in Illustration

*1	Front view of wire harness connector (to Position Control ECU and Switch Assembly)

Standard Resistance:

Tester Connection	Condition	Specified Condition
T11-8 (CANP) - T11-7 (CANN)	Ignition switch off	54 to 69 Ω

REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY BRANCH WIRE)

3.	CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)

(a) Disconnect the position control ECU and switch assembly connector.

Text in Illustration

*1	Front view of wire harness connector (to Position Control ECU and Switch Assembly)

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection	Condition	Specified Condition
T10-6 (+B) - Body ground	Always	11 to 14 V

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

4.	CHECK HARNESS AND CONNECTOR (GROUND TERMINAL)

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection	Condition	Specified Condition
T10-1 (GND) - Body ground	Always	Below 1 Ω

Text in Illustration

*1	Front view of wire harness connector (to Position Control ECU and Switch Assembly)

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

REPAIR OR REPLACE HARNESS OR CONNECTOR (GROUND CIRCUIT)

Lost Communication with Rear Gate Module (U0230)

DESCRIPTION DTC No. DTC Detection Condition Trouble Area U0230 No communication from the power back door ECU (back door motor unit) or ...

Lost Communication with "Door Control Module A" (U0199)

DESCRIPTION DTC No. DTC Detection Condition Trouble Area U0199 No communication from the outer mirror control ECU (for front passenger ...

Other materials about Toyota Venza:

Disassembly
DISASSEMBLY PROCEDURE 1. REMOVE SEAT ADJUSTER COVER CAP RH (a) Using a screwdriver wrapped with protective tape, disengage the 3 claws and remove the seat adjuster cover cap RH. Text in Illustration *1 ...

Installation
INSTALLATION PROCEDURE 1. INSTALL REAR POWER POINT SOCKET COVER (a) Engage the 2 claws to install the rear power point socket cover. 2. INSTALL REAR POWER POINT SOCKET ASSEMBLY (a) Engag ...

Data List / Active Test
DATA LIST / ACTIVE TEST 1. DATA LIST HINT: Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful bec ...