Toyota Venza: Lost Communication with Front Satellite Sensor Bus (B161A/8A)

Toyota Venza Service Manual / Supplemental Restraint Systems / Airbag System / Lost Communication with Front Satellite Sensor Bus (B161A/8A)

DESCRIPTION

The front collision sensor circuit (front airbag sensor RH circuit and front airbag sensor LH circuit) is composed of the center airbag sensor assembly, front airbag sensor RH and front airbag sensor LH.

The front airbag sensor RH or front airbag sensor LH detect impacts to the vehicle and send signals to the center airbag sensor assembly to determine if the airbag should be deployed.

DTC B161A/8A is stored when a malfunction is detected in the front collision sensor circuit (front airbag sensor RH circuit and front airbag sensor LH circuit).

DTC No.	DTC Detection Condition	Trouble Area
B161A/8A	The center airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the front collision sensor circuit (front airbag sensor RH circuit and front airbag sensor LH circuit). Front airbag sensor RH malfunction Front airbag sensor LH malfunction Center airbag sensor assembly malfunction	Instrument panel wire Engine room main wire Front airbag sensor RH Front airbag sensor LH Center airbag sensor assembly

WIRING DIAGRAM

PROCEDURE

CHECK DTC

(a) Turn the ignition switch to ON, and wait for at least 60 seconds.

(b) Turn the ignition switch off.

HINT:

If a communication error occurs, DTCs for both LH and RH sides will be stored simultaneously. To identify the malfunctioning area, turn the ignition switch off and then to ON again.

(d) Check for DTCs (See page ).

Result	Proceed to
DTCs B1613/83 and B1618/84 are not output.	A
DTC B1613/83 is output.	B
DTC B1618/84 is output.	C

HINT:

DTCs indicating communication errors will be changed to DTCs indicating errors in initialization by turning the ignition switch off and then to ON again.
Codes other than DTCs B1613/83 and B1618/84 may be output at this time, but they are not related to this check.

GO TO DTC B1613/83

GO TO DTC B1618/84

2.	CHECK CENTER AIRBAG SENSOR ASSEMBLY

(a) Turn the ignition switch to ON, and wait for at least 60 seconds.

(b) Clear the DTCs stored in memory (See page ).

(d) Turn the ignition switch to ON, and wait for at least 60 seconds.

(e) Check for DTCs (See page ).

OK:

DTC B161A/8A is not output.

HINT:

Codes other than DTC B161A/8A may be output at this time, but they are not related to this check.

USE SIMULATION METHOD TO CHECK

REPLACE CENTER AIRBAG SENSOR ASSEMBLY

Rear Airbag Sensor RH Circuit Malfunction (B1630/23)

DESCRIPTION The side collision sensor RH circuit (to determine deployment of the front seat side airbag assembly RH and curtain shield airbag assembly RH) is composed of the center airbag sensor ...

Lost Communication with Front Airbag Sensor LH (B1617/84,B1618/84)

DESCRIPTION The front airbag sensor LH circuit consists of the center airbag sensor assembly and front airbag sensor LH. The front airbag sensor LH detects impacts to the vehicle and sends signals ...

Other materials about Toyota Venza:

Reverse Shift-linked Function of Power Mirrors does not Operate
SYSTEM DESCRIPTION On receiving a reverse signal from the park/neutral position switch assembly, the ECM sends the reverse signal to the main body ECU (driver side junction block assembly) via CAN communication. When receiving the reverse signal, the main ...

Communication Malfunction No. 1 (B2797)
DESCRIPTION This DTC is stored when an error occurs in communication between the transponder key amplifier and the transponder key ECU assembly. HINT: Some noise is found in the communication line. DTC No. DTC Detection Condition ...

Data List / Active Test
DATA LIST / ACTIVE TEST 1. DATA LIST HINT: Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful bec ...