DESCRIPTION
The engine control unit communicates with the TCM using the Controller Area Network (CAN).
If there is a problem in this communication, the TCM sets a DTC.
DTC No. |
DTC Detection Condition |
Trouble Area |
---|---|---|
U0100 |
Following conditions are met for 1.25 seconds (1 trip detection logic):
|
|
MONITOR STRATEGY
Related DTCs |
U0100: Verify communication |
Required Sensors/Components (Main) |
TCM |
Required Sensors/Components (Related) |
- |
Frequency of Operation |
Continuous |
Duration |
1.25 seconds |
MIL Operation |
Immediate |
Sequence of Operation |
None |
TYPICAL ENABLING CONDITIONS
Monitor runs whenever following DTCs not present |
None |
Battery Voltage |
10.5 V or more |
Ignition Switch |
ON |
Starter |
OFF |
TYPICAL MALFUNCTION THRESHOLDS
Communication between TCM and ECM |
No communication |
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
Perform the universal trip to clear permanent DTCs (See page ).
HINT:
PROCEDURE
1. |
CHECK ECU TERMINAL VOLTAGE (+B AND E1 TERMINALS) |
(a) Disconnect the TCM connector. |
|
(b) Turn the ignition switch to ON.
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection |
Switch Condition |
Specified Condition |
---|---|---|
B40-18 (+B) - B40-8 (E1) |
Ignition switch ON |
9 to 14 V |
(d) Turn the ignition switch off.
(e) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection |
Condition |
Specified Condition |
---|---|---|
B40-8 (E1) - Body ground |
Always |
Below 1 Ω |
*1 |
Front view of wire harness connector (to TCM) |
NG |
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
2. |
CHECK HARNESS AND CONNECTOR (TCM - ECM) |
(a) Disconnect the TCM connector. |
|
(b) Disconnect the ECM connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection |
Condition |
Specified Condition |
---|---|---|
B40-6 (CAN+) - B39-24 (CAN+) |
Always |
Below 1 Ω |
B40-7 (CAN-) - B39-1 (CAN-) |
Always |
Below 1 Ω |
B40-6 (CAN+) or B39-24 (CAN+) - Body ground or other terminals |
Always |
1 MΩ or higher |
B40-7 (CAN-) or B39-1 (CAN-) - Body ground or other terminals |
Always |
1 MΩ or higher |
*1 |
Front view of wire harness connector (to ECM) |
*2 |
Front view of wire harness connector (to TCM) |
NG |
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
3. |
CHECK IF DTC OUTPUT RECURS |
(a) Connect the Techstream to the DLC3.
(b) Clear the DTCs.
(c) Replace the TCM.
HINT:
Replace the TCM with a TCM from a normally functioning vehicle of the same model.
(d) Start the engine.
(e) Read the DTCs.
Display (DTC Output) |
Proceed to |
---|---|
U0100 |
A |
No DTC |
B |
A |
REPLACE ECM |
B |
REPLACE TCM |
Satellite Radio Broadcast cannot be Received
CAUTION / NOTICE / HINT
NOTICE:
Some satellite radio broadcasts require payment. A contract must be made between
a satellite radio company and the user. If the contract expires, it will not be
possible to listen to the broadcast.
PROCEDURE
1 ...
System Description
SYSTEM DESCRIPTION
1. BACK DOOR CLOSER SYSTEM DESCRIPTION
(a) Operating any power back door switch when the back door is fully closed inputs
a request signal to the power back door ECU*1 or back door closer ECU*2. The power
back door ECU*1 or back door c ...
Chassis
General Maintenance
GENERAL MAINTENANCE
PROCEDURE
1. INSPECT STEERING LINKAGE AND GEAR HOUSING
(a) Check the steering wheel free play (See page
).
(b) Check the steering linkage for looseness or damage.
(1) Check that the tie rod ends do not have any ...