Toyota Venza: LIN Communication Master Malfunction (B2287)

Toyota Venza Service Manual / Networking / Lin Communication System / LIN Communication Master Malfunction (B2287)

DESCRIPTION

This DTC is stored when there is an open, short or ECU communication malfunction between the power management control ECU and certification ECU (smart key ECU assembly).

DTC No.	DTC Detection Condition	Trouble Area
B2287	There is an open, short or ECU communication malfunction between the power management control ECU and certification ECU (smart key ECU assembly).	Power management control ECU Certification ECU (Smart key ECU assembly) Wire harness or connector

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

If the certification ECU (smart key ECU assembly) is replaced, register the key.
When using the Techstream to troubleshoot with the ignition switch off:
Connect the Techstream to the DLC3, and turn the courtesy switch on and off at 1.5-second intervals until communication between the Techstream and vehicle begins.

PROCEDURE

1.	CHECK DTC OUTPUT

(a) Clear the DTC (See page ).

(b) Recheck for DTCs.

HINT:

Check for certification ECU and power source control ECU DTCs.

Result	Proceed to
Only DTC B2287 is output.	A
DTC B2287 and B2785 are output simultaneously.	B

HINT:

When DTC B2287 and B2785 are output simultaneously, perform troubleshooting for DTC B2785 first.

GO TO DTC B2785

2.	CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - POWER MANAGEMENT CONTROL ECU)

(a) Disconnect the D25 and D43 ECU connectors.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection	Condition	Specified Condition
D25-29 (LIN) - D43-24 (LIN2)	Always	Below 1 Ω
D25-29 (LIN) - Body ground	Always	10 kΩ or higher

Text in Illustration

Front view of wire harness connector

(to Certification ECU (Smart Key ECU Assembly)

Front view of wire harness connector

(to Power Management Control ECU)

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.	REPLACE POWER MANAGEMENT CONTROL ECU

(a) Replace the power management control ECU (See page ).

4.	CHECK DTC OUTPUT

(a) Clear the DTC (See page ).

(b) Recheck for DTCs.

OK:

DTC B2287 is not output.

END (POWER MANAGEMENT CONTROL ECU WAS DEFECTIVE)

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

Sliding Roof ECU Communication Stop (B1273)

DESCRIPTION This DTC is stored when LIN communication between the sliding roof ECU (sliding roof drive gear sub-assembly) and main body ECU (driver side junction block assembly) stops for more th ...

Lost Communication with AFS LIN (B124D)

DESCRIPTION Refer to DTC B124D (Lighting system) (See page ). DTC No. DTC Detection Condition Trouble Area B124D Malfunctions in LIN co ...

Other materials about Toyota Venza:

CD cannot be Inserted / Played or CD is Ejected Right After Insertion
PROCEDURE 1. CHECK IF A PROPER CD IS INSERTED (a) Make sure that the CD is an audio CD or a CD with an MP3, WMA or AAC file, and that it is not deformed, flawed, stained, deteriorated or otherwise defective. OK: CD is nor ...

Removal
REMOVAL PROCEDURE 1. REMOVE REAR DOOR SCUFF PLATE LH 2. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH 3. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover) 4. REMOVE DECK BOARD ASSEMBLY 5. REMOVE NO. 3 DECK BOARD SUB-ASSEMBLY 6. REMOVE DECK ...

Removal
REMOVAL CAUTION / NOTICE / HINT HINT: Perform "Inspection After Repair" after replacing the fuel injector assembly (See page ). PROCEDURE 1. DISCHARGE FUEL SYSTEM PRESSURE (a) Discharge fuel system pressure (See page ). 2. DISCONNECT CABL ...