Toyota Venza: Jam Protection Function Activates During Power Back Door Operation

Toyota Venza Service Manual / Door / Hatch / Power Back Door System / Jam Protection Function Activates During Power Back Door Operation

DESCRIPTION

When the jam protection function activates during power back door operation, one of the following may be the cause: 1) improper fit of back door, or a foreign object is stuck in the back door, 2) malfunctioning power back door touch sensor circuit or 3) malfunctioning power back door ECU (power back door motor unit).

WIRING DIAGRAM

PROCEDURE

1.	CHECK BACK DOOR LOCK FUNCTION

(a) Check if there are any foreign objects interfering with back door operation.

OK:

There are no foreign objects.

REMOVE FOREIGN OBJECT

2.	CHECK BACK DOOR

(a) Check back door operation.

(1) Turn the power back door main switch off.

(2) Open/close the back door by hand.

OK:

The back door fully opens and closes smoothly.

ADJUST BACK DOOR

3.	READ VALUE USING TECHSTREAM (POWER BACK DOOR TOUCH SENSOR)

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(d) Enter the following menus: Body Electrical / Back Door / Data List.

(e) Check the Data List to determine if the power back door touch sensor functions properly.

Back Door (Power Back Door ECU)

Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
PBD Touch Sensor (Right)	Power back door touch sensor RH signal / ON , OFF or Open	ON: Power back door touch sensor RH pressed OFF: Power back door touch sensor RH not pressed Open: Power back door touch sensor RH circuit open	-
PBD Touch Sensor (Left)	Power back door touch sensor LH signal / ON , OFF or Open	ON: Power back door touch sensor LH pressed OFF: Power back door touch sensor LH not pressed Open: Power back door touch sensor LH circuit open	-

Tester Display

Measurement Item/Range

Normal Condition

Diagnostic Note

PBD Touch Sensor (Right)

Power back door touch sensor RH signal / ON , OFF or Open

ON: Power back door touch sensor RH pressed

OFF: Power back door touch sensor RH not pressed

Open: Power back door touch sensor RH circuit open

PBD Touch Sensor (Left)

Power back door touch sensor LH signal / ON , OFF or Open

ON: Power back door touch sensor LH pressed

OFF: Power back door touch sensor LH not pressed

Open: Power back door touch sensor LH circuit open

Result	Proceed to
On the Techstream screen, ON or OFF will be displayed accordingly.	A
On the Techstream screen, ON or OFF will not be displayed accordingly or Open is displayed.	B

REPLACE POWER BACK DOOR ECU (POWER BACK DOOR MOTOR UNIT)

GO TO OTHER FLOW CHART (TOUCH SENSOR CIRCUIT)

Power Back Door cannot be Closed Using the Power Back Door Closer Switch

DESCRIPTION When the power back door cannot be closed using the power back door closer switch, either of the following may be malfunctioning: 1) power back door closer switch circuit or 2) power ...

Power Back Door Warning System does not Operate

DESCRIPTION When the power back door warning system does not operate, one of the following may be malfunctioning: 1) power back door warning buzzer circuit, 2) wireless door lock control system o ...

Other materials about Toyota Venza:

Removal
REMOVAL PROCEDURE 1. PRECAUTION (See page ) NOTICE: After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable fr ...

Engine Coolant Temperature Circuit Range / Performance Problem (P0116)
DESCRIPTION Refer to DTC P0115 (See page ). DTC No. DTC Detection Condition Trouble Area P0116 When either of the following conditions is met (2 trip detection logic). During engine ...

Inspection
INSPECTION PROCEDURE 1. INSPECT FUEL PUMP ASSEMBLY WITH FILTER (a) Inspect fuel pump resistance. (1) Measure the resistance according to the value(s) in the table below. Standard Resistance: Tester Connection Condition ...