INSTALLATION
PROCEDURE
1. INSTALL MANUAL VALVE
(a) Coat the manual valve with ATF and install it to the transmission valve body assembly.
2. SUPPORT ENGINE ASSEMBLY
3. INSTALL TRANSMISSION VALVE BODY ASSEMBLY
(a) Coat the O-ring of the transmission wire with ATF.
(b) Insert the pin of the manual valve lever shaft sub-assembly into the groove on the end of the manual valve and install the transmission valve body assembly to the automatic transaxle assembly with the 11 bolts. Text in Illustration
Torque: 11 N·m {112 kgf·cm, 8 ft·lbf} Bolt Length: Bolt (A) 25 mm (0.984 in.) Bolt (B) 30 mm (1.18 in.) Bolt (C) 35 mm (1.38 in.) Bolt (D) 45 mm (1.77 in.) Bolt (E) 55 mm (2.17 in.) NOTICE:
|
|
4. INSTALL VALVE BODY OIL STRAINER ASSEMBLY
(a) Coat a new O-ring with ATF and install it to the valve body oil strainer assembly.
NOTICE:
Ensure that the O-ring is not twisted or pinched.
(b) Install the valve body oil strainer assembly to the transmission valve body assembly with the 2 bolts. Torque: 11 N·m {112 kgf·cm, 8 ft·lbf} |
|
5. INSTALL TRANSMISSION OIL CLEANER MAGNET
(a) Install the 2 transmission oil cleaner magnets to the automatic transaxle oil pan sub-assembly as shown in the illustration. Text in Illustration
|
|
6. INSTALL AUTOMATIC TRANSAXLE OIL PAN GASKET
(a) Install a new automatic transaxle oil pan gasket to the automatic transaxle oil pan sub-assembly.
7. INSTALL AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY
(a) Clean and degrease the bolt and the bolt hole in the automatic transaxle assembly. |
|
(b) Install the automatic transaxle oil pan sub-assembly with automatic transaxle oil pan gasket to the automatic transaxle assembly with the 17 bolts. Torque: 7.5 N·m {76 kgf·cm, 66 in·lbf} NOTICE: Completely remove any oil or grease from the contact surfaces of the automatic transaxle assembly and automatic transaxle oil pan sub-assembly with automatic transaxle oil pan gasket before installation. |
|
(c) Apply adhesive to 2 or 3 threads on the end of the bolt.
Adhesive:
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
NOTICE:
In order to ensure proper sealing of the bolt, apply adhesive to the bolt and install it within 10 minutes of adhesive application.
(d) Install the bolt. Torque: 7.0 N·m {71 kgf·cm, 62 in·lbf} |
|
8. INSTALL BELT
9. INSTALL FRONT FRAME ASSEMBLY
See page
10. ADD AUTOMATIC TRANSAXLE FLUID
See page
11. CHECK AUTOMATIC TRANSAXLE SYSTEM
NOTICE:
If automatic transaxle assembly parts have been replaced, refer to Parts Replacement Compensation Table to determine if any additional operations are necessary (See page ).
Selecting the units
Press the “US/M-M” button.
The unit changes each time the button is pressed.
- Liquid crystal display
Small spots or light spots may appear on the display. This phenomenon is characteristic
of liquid crystal displays, and there is no problem to ...
Reassembly
REASSEMBLY
CAUTION / NOTICE / HINT
NOTICE:
Before installation, apply high temperature grease to the parts indicated by
arrows (See page ).
PROCEDURE
1. INSTALL NO. 2 PARKING BRAKE SHOE HOLD DOWN SPRING PIN (for 2WD)
(a) Install the No. 2 p ...
How To Proceed With Troubleshooting
CAUTION / NOTICE / HINT
HINT:
Use the following procedure to troubleshoot the power window control
system.
*: Use the Techstream.
PROCEDURE
1.
VEHICLE BROUGHT TO WORKSHOP
NEXT
...