Toyota Venza manuals

Toyota Venza: Installation

INSTALLATION

CAUTION / NOTICE / HINT

HINT:

  • Use the same procedure for the RH side and LH side.
  • The procedure listed below is for the LH side.

PROCEDURE

1. INSTALL REAR AXLE HUB AND BEARING ASSEMBLY

(a) Apply a total of 0.1 to 0.3g (0.00353 to 0.0105 oz.) of Toyota Body Grease W to the 8 areas shown in the illustration.

Text in Illustration

Toyota Body Grease W

(b) Align the matchmarks on the rear drive shaft assembly and the rear axle hub and bearing assembly.

Text in Illustration

*1

Matchmark

NOTICE:

Do not rotate the rear drive shaft.


(c) Install the parking brake assembly and the rear axle hub and bearing assembly with the 4 bolts.

Torque:

80 N·m {816 kgf·cm, 59 ft·lbf}

NOTICE:

Do not twist the parking brake cable assembly when installing it.


2. INSTALL REAR AXLE SHAFT NUT

(a) Clean the threaded parts on the rear drive shaft assembly and a new rear axle shaft nut using a non-residue solvent.

NOTICE:

  • Be sure to perform this work for a new rear drive shaft assembly.
  • Keep the threaded parts free of oil and foreign matter.

(b) install the rear disc with the 5 hub nuts.

(c) While applying the parking brakes, temporarily install the new rear axle shaft nut.

Torque:

294 N·m {2998 kgf·cm, 217 ft·lbf}

NOTICE:

Stake the nut after inspecting for looseness and runout in the following steps.

(d) Remove the 5 hub nuts and the rear disc.

3. INSTALL REAR SPEED SENSOR

(a) Install the rear speed sensor to the rear axle carrier sub-assembly with the bolt.

Torque:

8.5 N·m {87 kgf·cm, 75 in·lbf}

NOTICE:

  • Keep the rear speed sensor tip and sensor installation hole free of foreign matter.
  • Do not twist the rear speed sensor wire when installing it.

4. INSPECT REAR AXLE HUB BEARING LOOSENESS


5. INSPECT REAR AXLE HUB RUNOUT


6. INSTALL REAR DISC


7. INSTALL REAR DISC BRAKE CALIPER ASSEMBLY


8. STAKE REAR AXLE SHAFT NUT

(a) Using a chisel and a hammer, stake the rear axle shaft nut.


9. INSTALL REAR WHEEL

Torque:

103 N·m {1050 kgf·cm, 76 ft·lbf}

10. CHECK FOR SPEED SENSOR SIGNAL

(a) Check for the speed sensor signal (See page ).


On-vehicle Inspection
ON-VEHICLE INSPECTION CAUTION / NOTICE / HINT HINT: Use the same procedure for the RH side and LH side. The procedure listed below is for the LH side. PROCEDURE 1. REMOVE REAR W ...

Removal
REMOVAL CAUTION / NOTICE / HINT HINT: Use the same procedure for the RH side and LH side. The procedure listed below is for the LH side. PROCEDURE 1. REMOVE REAR WHEEL 2. SEPAR ...

Other materials about Toyota Venza:

Components
COMPONENTS ILLUSTRATION ILLUSTRATION ILLUSTRATION ILLUSTRATION ILLUSTRATION ILLUSTRATION ...

Removal
REMOVAL CAUTION / NOTICE / HINT CAUTION: Wear protective gloves when removing the exhaust pipe. The exhaust pipe is extremely hot immediately after the engine has stopped. Confirm that the exhaust pipe has cooled down ...

Personal Light
Components COMPONENTS ILLUSTRATION Removal REMOVAL PROCEDURE 1. REMOVE MAP LIGHT ASSEMBLY (a) Using a moulding remover, disengage the 2 claws and 2 clips. Text in Illustration *1 Fastener ...

© 2016-2024 Copyright www.tovenza.com

0.141