Toyota Venza: Installation

Toyota Venza Service Manual / Axle And Differential / Rear Axle Carrier(for 2wd) / Installation

INSTALLATION

CAUTION / NOTICE / HINT

HINT:

Use the same procedure for the RH side and LH side.
The procedure listed below is for the LH side.

PROCEDURE

1. INSTALL REAR AXLE CARRIER SUB-ASSEMBLY

(a) Temporarily install the rear axle carrier sub-assembly with the 2 bolts and 2 nuts.

(b) Install the rear axle carrier sub-assembly with the 2 bolts and 2 nuts.

Torque:

290 N·m {2957 kgf·cm, 214 ft·lbf}

NOTICE:

When installing the nuts, keep the bolts from rotating.

2. INSTALL REAR STRUT ROD ASSEMBLY

3. INSTALL NO. 3 PARKING BRAKE CABLE ASSEMBLY

4. INSTALL REAR AXLE HUB AND BEARING ASSEMBLY

5. INSTALL REAR SPEED SENSOR WIRE

6. INSTALL REAR DISC

7. INSTALL REAR DISC BRAKE CALIPER ASSEMBLY

8. STABILIZE SUSPENSION

9. FULLY TIGHTEN REAR NO. 1 SUSPENSION ARM ASSEMBLY

(a) Support the rear axle carrier sub-assembly using a jack and wooden block as shown in the illustration.

Text in Illustration

*1	Wooden Block
*2	Jack

NOTICE:

Do not bend the brake dust cover.

(b) Jack up the rear axle carrier sub-assembly LH to set the rear No. 1 suspension arm assembly LH in the tightening position as shown in the illustration.

Standard angle (A):

4°36' (4.6°)

Standard length (B):

38.6 mm (1.52 in.)

CAUTION:

Do not jack up the rear axle carrier sub-assembly LH too high as the vehicle may fall.

HINT:

If the rear No. 1 suspension arm assembly LH cannot be positioned as shown in the illustration even when the rear axle carrier sub-assembly LH is jacked up, apply additional load to the vehicle such as by having a person sit in the rear seat.

Torque:

112 N·m {1141 kgf·cm, 82 ft·lbf}

NOTICE:

Since a stopper nut is used, fully tighten the bolt.
The final torque must be applied under standard vehicle height conditions.

10. FULLY TIGHTEN REAR NO. 2 SUSPENSION ARM ASSEMBLY

(a) Support the rear axle carrier sub-assembly using a jack and wooden block as shown in the illustration.

Text in Illustration

*1	Wooden Block
*2	Jack

NOTICE:

Do not bend the brake dust cover.

(b) Jack up the rear axle carrier sub-assembly LH to set the rear No. 2 suspension arm assembly LH in the tightening position as shown in the illustration.

Standard angle (A):

4°36' (4.6°)

Standard length (B):

39.1 mm (1.54 in.)

CAUTION:

Do not jack up the rear axle carrier sub-assembly LH too high as the vehicle may fall.

HINT:

If the rear No. 2 suspension arm assembly LH cannot be positioned as shown in the illustration even when the rear axle carrier sub-assembly LH is jacked up, apply additional load to the vehicle such as by having a person sit in the rear seat.

Torque:

112 N·m {1141 kgf·cm, 82 ft·lbf}

NOTICE:

Since a stopper nut is used, fully tighten the bolt.
The final torque must be applied under standard vehicle height conditions.

11. INSTALL REAR WHEEL

Torque:

103 N·m {1050 kgf·cm, 76 ft·lbf}

12. INSPECT AND ADJUST REAR WHEEL ALIGNMENT

(a) Inspect and adjust the front wheel alignment (See page ).

13. CHECK FOR SPEED SENSOR SIGNAL

(a) Check for the speed sensor signal (See page ).

Removal

REMOVAL CAUTION / NOTICE / HINT HINT: Use the same procedure for the RH side and LH side. The procedure listed below is for the LH side. PROCEDURE 1. REMOVE REAR WHEEL 2. SEPAR ...

Rear Axle Carrier(for Awd)

...

Other materials about Toyota Venza:

Glove Box Light
Components COMPONENTS ILLUSTRATION Inspection INSPECTION PROCEDURE 1. INSPECT GLOVE BOX LIGHT ASSEMBLY (a) Connect a positive (+) lead from the battery to terminal 1 and a negative (-) lead to terminal 2. ...

Terminals Of Ecu
TERMINALS OF ECU NOTICE: Turn the ignition switch off before measuring the resistances between CAN bus main wires and between CAN bus branch wires. Turn the ignition switch off before inspecting CAN bus wires for a ground short. After ...

Engine coolant
The coolant level is satisfactory if it is between the “F” and “L” lines on the reservoir when the engine is cold. 1. Reservoir cap 2. Full 3. Low If the level is on or below the “L” line, add coolant up to the “F” line. - If the ...