Toyota Venza manuals

Toyota Venza: Installation

INSTALLATION

PROCEDURE

1. INSTALL NO. 3 PARKING BRAKE CABLE ASSEMBLY

(a) Install the No. 3 parking brake cable assembly with the bolt and 4 nuts.


Torque:

Nut (A) :

5.4 N·m {55 kgf·cm, 48 in·lbf}

Nut (B) :

6.0 N·m {61 kgf·cm, 53 in·lbf}

Bolt :

6.0 N·m {61 kgf·cm, 53 in·lbf}

(b) Install the No. 3 parking brake cable assembly to the backing plate with the 2 bolts.

Torque:

8.0 N·m {82 kgf·cm, 71 in·lbf}


2. INSTALL NO. 2 PARKING BRAKE CABLE ASSEMBLY

HINT:

Use the same procedure as for the No. 3 parking brake cable assembly.

3. INSTALL NO. 2 PARKING BRAKE SHOE ASSEMBLY WITH PARKING BRAKE SHOE LEVER

(a) Refer to the instructions for Installation of the No. 2 parking brake shoe assembly with parking brake shoe lever (See page ).


4. INSTALL REAR WHEEL

Torque:

103 N·m {1050 kgf·cm, 76 ft·lbf}

5. INSTALL PARKING BRAKE EQUALIZER

(a) Connect the No. 2 parking brake cable assembly and No. 3 parking brake cable assembly to the parking brake equalizer to install it.

NOTICE:

The slits of the parking brake equalizer face upward.


6. INSTALL NO. 4 PARKING BRAKE CABLE ASSEMBLY

(a) Install the No. 4 parking brake cable assembly with the 2 bolts.

Torque:

21 N·m {214 kgf·cm, 15 ft·lbf}


(b) Connect the No. 4 parking brake cable assembly to the parking brake equalizer as shown in the illustration.


(c) Slide the rubber boot to engage it as shown in the illustration.


7. INSTALL NO. 1 PARKING BRAKE CABLE ASSEMBLY

(a) Pass the No. 1 parking brake cable assembly through the parking brake pedal assembly.

(b) Install a new clip to the No. 1 parking brake cable assembly.


(c) Depress the parking brake pedal.


(d) Bend the parking brake pedal claw to hold the No. 1 parking brake cable assembly.


(e) Release the parking brake pedal.

8. INSTALL PARKING BRAKE PEDAL ASSEMBLY

HINT:

Refer to the instructions for Installation of the parking brake pedal assembly (See page ).


9. BED IN PARKING BRAKE SHOES TO DISCS


10. ADJUST PARKING BRAKE SHOE CLEARANCE AND PARKING BRAKE PEDAL TRAVEL


11. INSPECT BRAKE WARNING LIGHT


Removal
REMOVAL PROCEDURE 1. REMOVE PARKING BRAKE PEDAL ASSEMBLY HINT: Refer to the instructions for Removal of the parking brake pedal assembly (See page ). 2. REMOVE NO. 1 PARKING BRAKE CABLE ASSEMB ...

Parking Brake Pedal
...

Other materials about Toyota Venza:

Terminals Of Ecu
TERMINALS OF ECU 1. CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY (a) Disconnect the D47 air conditioning amplifier assembly connector. (b) Measure the voltage and resistance according to the value(s) in the table below. HINT: Measure the values on the wi ...

Back Door Closer does not Operate
DESCRIPTION When the back door closer does not operate, one of the following may be the cause: 1) improper fit of the back door, or a foreign object is stuck in the back door or 2) initialization of the power back door ECU (power back door motor unit)*1, ...

Illumination Circuit
DESCRIPTION Power is supplied to the navigation receiver assembly and steering pad switch assembly illumination when the light control switch is in the tail or head position. WIRING DIAGRAM CAUTION / NOTICE / HINT NOTICE: The vehicle is equipp ...

© 2016-2024 Copyright www.tovenza.com

0.1243