Toyota Venza: Installation

Toyota Venza Service Manual / Audio / Video / Radio Antenna Cord / Installation

INSTALLATION

PROCEDURE

1. INSTALL NO. 3 ANTENNA CORD SUB-ASSEMBLY

(a) Pass the washer hose through the No. 3 antenna cord sub-assembly.

(b) Pass the No. 3 antenna cord sub-assembly with washer hose through the vehicle body as shown in the illustration.

(d) Connect the grommet to the back door.

(e) Engage the 4 clamps.

Text in Illustration

Clamp

Grommet

(f) Connect the connector and engage the clamp.

(g) w/o Satellite Radio:

(1) Engage the 7 clamps.

(2) Engage the 4 hooks to connect the washer hose.

Text in Illustration

*1	Clamp	*2	Hook
*3	Washer Hose	-	-

(3) Connect the 2 connectors.

(h) w/ Satellite Radio:

(1) Engage the 5 clamps.

(2) Engage the 4 hooks to connect the washer hose.

Text in Illustration

*1	Clamp	*2	Hook
*3	Washer Hose	-	-

(3) Connect the connector.

(i) Set the position of the grommet as shown in the illustration.

Text in Illustration

Flat Area

HINT:

Flat area to be oriented outside the vehicle.

2. INSTALL BACK DOOR TRIM COVER RH

3. INSTALL BACK DOOR TRIM COVER LH (w/o Power Back Door)

4. INSTALL BACK DOOR TRIM COVER LH (w/ Power Back Door)

5. INSTALL BACK DOOR PANEL TRIM ASSEMBLY

6. INSTALL UPPER BACK WINDOW PANEL TRIM

7. INSTALL NO. 2 ANTENNA CORD SUB-ASSEMBLY (w/o Sliding Roof)

(a) Aligning the No. 2 antenna cord sub-assembly and washer hose with the markings on the roof headlining assembly, temporarily install the cord and washer hose.

Text in Illustration

	Tape	-	-
	Front	-	-

(b) Put the strips of the tape back to the positions shown in the illustration in order to secure the antenna cord and washer hose to the roof headlining assembly.

HINT:

If the tape has lost adhesion, use other tape, such as packing tape, with enough adhesion to secure the antenna cord and washer hose to the roof headlining assembly.
Secure the antenna cord and washer hose to the roof headlining assembly with tape as shown in the illustration.

8. INSTALL NO. 2 ANTENNA CORD SUB-ASSEMBLY (w/ Sliding Roof)

(a) Aligning the No. 2 antenna cord sub-assembly and washer hose with the markings on the roof headlining assembly, temporarily install the cord and washer hose.

Text in Illustration

	Tape	-	-
	Front	-	-

(b) Put the strips of the tape back to the positions shown in the illustration in order to secure the antenna cord and washer hose to the roof headlining assembly.

HINT:

If the tape has lost adhesion, use other tape, such as packing tape, with enough adhesion to secure the antenna cord and washer hose to the roof headlining assembly.
Secure the antenna cord and washer hose to the roof headlining assembly with tape as shown in the illustration.

9. INSTALL ROOF HEADLINING ASSEMBLY

(See page )

10. INSTALL NO. 1 ANTENNA CORD SUB-ASSEMBLY

(a) Engage the 7 clamps to install the No. 1 antenna cord sub-assembly.

11. INSTALL INSTRUMENT PANEL SAFETY PAD ASSEMBLY

(See page )

Removal

REMOVAL PROCEDURE 1. REMOVE INSTRUMENT PANEL SAFETY PAD ASSEMBLY (See page ) 2. REMOVE NO. 1 ANTENNA CORD SUB-ASSEMBLY (a) Disengage the 7 clamps and remove the No. 1 antenna cord sub-assembly. ...

Radio Antenna Pole

Components COMPONENTS ILLUSTRATION Removal REMOVAL PROCEDURE 1. REMOVE ROOF ANTENNA POLE SUB-ASSEMBLY (a) Turn the roof antenna pole sub-assembly in the direction indicated ...

Other materials about Toyota Venza:

Sliding Roof Switch Assembly
Components COMPONENTS ILLUSTRATION Removal REMOVAL PROCEDURE 1. REMOVE MAP LIGHT ASSEMBLY Inspection INSPECTION PROCEDURE 1. INSPECT SLIDING ROOF SWITCH (ROOF CONSOLE BOX ASSEMBLY) (a) Measure the resistance according to the value(s) in ...

ECU Power Source Circuit
DESCRIPTION This circuit provides power for main body ECU (driver side junction block assembly) operation. WIRING DIAGRAM PROCEDURE 1. CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY (MAIN BODY ECU (POWER SOURCE)) ...

Sliding Roof ECU Communication Stop (B1273)
DESCRIPTION This DTC is stored when LIN communication between the sliding roof ECU (sliding roof drive gear sub-assembly) and main body ECU (driver side junction block assembly) stops for more than 10 seconds. DTC No. DTC Detection ...