Toyota Venza manuals

Toyota Venza: Installation

INSTALLATION

CAUTION / NOTICE / HINT

HINT:

  • Use the same procedure for the RH side and LH side.
  • The procedure listed below is for the LH side.

PROCEDURE

1. INSTALL DOOR SIDE AIRBAG SENSOR

(a) Check that the ignition switch is off.

(b) Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

(c) Insert the pin (stopper) into the door hole and install the door side airbag sensor to the vehicle with the bolt.

Torque:

9.0 N·m {92 kgf·cm, 80 in·lbf}

NOTICE:

  • If the door side airbag sensor has been dropped, or there are any cracks, dents or other defects in the case or connector, replace it with a new one.
  • When installing the door side airbag sensor, be careful that the SRS wiring does not interfere with or is not pinched between other parts.
  • Make sure that the pin (stopper) is securely inserted into the door hole.
  • Tighten the bolt while holding the door side airbag sensor because the door side airbag sensor pin (stopper) is easily damaged.

(d) Connect the connector to the door side airbag sensor.

NOTICE:

When connecting the airbag connector, take care not to damage the airbag wire harness.

(1) Connect the connector as shown in the illustration (when locking, make sure that the outer connector locking sleeve returns to its original position and a click sound can be heard).

Text in Illustration

*1

Outer Connector Locking Sleeve

-

-

HINT:

When connected, the outer connector locking sleeve will slide. Be sure not to hold the outer connector locking sleeve while connecting, as it may result in an insecure fit.

(e) Check that there is no looseness in the installation parts of the door side airbag sensor.

2. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY


3. INSTALL COURTESY LIGHT ASSEMBLY


4. INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)


5. INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)


6. INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG


7. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page ).


8. PERFORM DIAGNOSTIC SYSTEM CHECK

(a) Perform a diagnostic system check (See page ).


9. INSPECT SRS WARNING LIGHT

(a) Inspect the SRS warning light (See page ).


Removal
REMOVAL CAUTION / NOTICE / HINT HINT: Use the same procedure for the RH side and LH side. The procedure listed below is for the LH side. PROCEDURE 1. PRECAUTION CAUTION: Be su ...

Spiral Cable
...

Other materials about Toyota Venza:

Reassembly
REASSEMBLY PROCEDURE 1. INSTALL NO. 1 CENTER SUPPORT BEARING ASSEMBLY (a) Set the No. 1 center support bearing on the intermediate shaft as shown in the illustration. NOTICE: Make sure to install the bearing in the correct position. ...

Headlight Solenoid Circuit
DESCRIPTION for HID Headlight: When the main body ECU receives a high beam turn on signal, the main body ECU activates the bi-function by controlling the BI-XENON relay. The bi-function increases the upper illumination area of the discharge ...

Headlight Leveling ECU Power Source Circuit
DESCRIPTION This circuit detects the state of the ignition switch, and sends it to the headlight leveling ECU assembly. WIRING DIAGRAM CAUTION / NOTICE / HINT NOTICE: Inspect the fuses for circuits related to this system before performing the followin ...

© 2016-2022 Copyright www.tovenza.com

0.132