Toyota Venza: Installation

Toyota Venza Service Manual / Supplemental Restraint Systems / Front Airbag Sensor / Installation

INSTALLATION

CAUTION / NOTICE / HINT

HINT:

Use the same procedure for the RH side and LH side.
The procedure listed below is for the LH side.

PROCEDURE

1. INSTALL FRONT AIRBAG SENSOR

(a) Check that the ignition switch is off.

(b) Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

Text in Illustration

*1	Torque Wrench Fulcrum Length

(d) Using SST, install the front airbag sensor with the bolt.

SST: 09961-00950

Torque:

Specified tightening torque :

9.0 N·m {92 kgf·cm, 80 in·lbf}

NOTICE:

This torque value is effective when SST is parallel to the torque wrench.
If the front airbag sensor has been dropped, or there are any cracks, dents or other defects in the case or connector, replace it with a new one.
When installing the front airbag sensor, be careful that the SRS wiring does not interfere with or is not pinched between other parts.
Make sure that the pin (stopper) is securely inserted into the body hole.
Tighten the bolt while holding the front airbag sensor because the front airbag sensor pin (stopper) is easily damaged.

HINT:

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench (See page ).
When using SST (fulcrum length of 150 mm (5.91 in.)) + torque wrench (fulcrum length of 250 mm (9.84 in.)):
5.6 N*m (57 kgf*cm, 50 in.*lbf)

(e) Connect the connector to the front airbag sensor.

NOTICE:

When connecting the airbag connector, take care not to damage the airbag wire harness.

(1) Before connecting the connector, check that the position of the white housing lock is correct as shown in the illustration.

(2) Be sure to engage the connectors until they are locked (When locking, make sure that a click sound can be heard).

HINT:

When engaged, the white housing lock will slide. Be sure not to hold the white housing lock and part (A), as it may result in an insecure fit.

(f) Check that there is no looseness in the installation parts of the front airbag sensor.

(g) Install the radiator side deflector LH with the 2 claws as shown in the illustration.

2. INSTALL RADIATOR GRILLE

3. INSTALL COOL AIR INTAKE DUCT SEAL

4. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page ).

5. PERFORM DIAGNOSTIC SYSTEM CHECK

(a) Perform a diagnostic system check (See page ).

6. INSPECT SRS WARNING LIGHT

(a) Inspect the SRS warning light (See page ).

Removal

REMOVAL CAUTION / NOTICE / HINT HINT: Use the same procedure for the RH side and LH side. The procedure listed below is for the LH side. PROCEDURE 1. PRECAUTION CAUTION: Be su ...

Front Passenger Airbag Assembly

...

Other materials about Toyota Venza:

Seat Belt Buckle Switch LH Circuit Malfunction (B1656/38)
DESCRIPTION The seat belt buckle switch LH circuit consists of the center airbag sensor assembly and front seat inner belt assembly LH. DTC B1656/38 is stored when a malfunction is detected in the seat belt buckle switch LH circuit. DTC No. ...

Inspection
INSPECTION PROCEDURE 1. INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY (a) Measure the resistance according to the value(s) in the table below when the shift lever is moved to each position. Text in Illustration *1 ...

Installation
INSTALLATION PROCEDURE 1. INSTALL REAR DRIVE SHAFT ASSEMBLY (a) Align the shaft splines and install the rear drive shaft assembly using a screwdriver and hammer. NOTICE: Set the snap ring with the opening facing downward. ...