Toyota Venza manuals

Toyota Venza: Installation

INSTALLATION

PROCEDURE

1. INSTALL CENTER AIRBAG SENSOR ASSEMBLY

(a) Check that the ignition switch is off.

(b) Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

(c) Install the center airbag sensor assembly with the 3 bolts.

Text in Illustration

*1

Waterproof Sheet

Torque:

18 N·m {178 kgf·cm, 13 ft·lbf}

NOTICE:

  • If the center airbag sensor assembly has been dropped, or there are any cracks, dents or other defects in the case or connector, replace it with a new one.
  • When installing the center airbag sensor assembly, be careful that the SRS wiring does not interfere with or is not pinched between other parts.
  • When the ignition switch is first turned to on after the center airbag sensor assembly has been replaced, make sure that no one is in the vehicle.

(d) Connect the connector to the center airbag sensor assembly as shown in the illustration.

NOTICE:

When connecting the airbag connector, take care not to damage the airbag wire harness.

(e) Check that the waterproof sheet is properly set.

(f) Check that there is no looseness in the installation parts of the center airbag sensor assembly.

2. INSTALL CONSOLE BOX SUB-ASSEMBLY


3. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY


4. INSTALL CONSOLE BOX ASSEMBLY


5. INSTALL NO. 2 CONSOLE BOX CARPET


6. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY


7. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


8. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH


9. INSTALL FRONT DOOR SCUFF PLATE RH


10. INSTALL AIR CONDITIONER CONTROL ASSEMBLY


11. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY (w/o Seat Heater System)


12. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY (w/ Seat Heater System)


13. INSTALL LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL


14. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH


15. INSTALL FRONT DOOR SCUFF PLATE LH


16. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page ).


17. PERFORM DIAGNOSTIC SYSTEM CHECK

(a) Perform a diagnostic system check (See page ).


18. INSPECT SRS WARNING LIGHT

(a) Inspect the SRS warning light (See page ).


Removal
REMOVAL PROCEDURE 1. PRECAUTION CAUTION: Be sure to read Precaution thoroughly before servicing (See page ). 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL CAUTION: Wait at least 90 secon ...

Curtain Shield Airbag Assembly
...

Other materials about Toyota Venza:

No Answer-Back
DESCRIPTION In some cases, wireless door lock control functions are normal but the hazard warning light and/or wireless door lock buzzer answer-back function(s) does not operate. In such cases, the main body ECU (driver side junction block assembly) haz ...

System Description
SYSTEM DESCRIPTION 1. AUTOMATIC LIGHT CONTROL SYSTEM When the light control switch is in the AUTO position, the automatic light control system detects ambient light levels and controls the low beam headlights, parking lights, taillights, marker lights an ...

Installation
INSTALLATION PROCEDURE 1. INSTALL FUEL LID LOCK CONTROL CABLE SUB-ASSEMBLY (a) Engage the 8 clamps. (b) Engage the 2 claws and connect the fuel lid lock control cable sub-assembly. 2. INSTALL FUE ...

© 2016-2024 Copyright www.tovenza.com

0.1416