Toyota Venza: Installation

Toyota Venza Service Manual / Wiper / Washer / Front Wiper Motor / Installation

INSTALLATION

PROCEDURE

1. INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY

(a) Using a T30 "TORX" socket wrench, install the windshield wiper motor assembly with the 2 bolts.

Torque:

7.5 N·m {76 kgf·cm, 66 in·lbf}

(b) Apply MP grease to the crank arm pivot of the windshield wiper motor assembly.

2. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

(a) Install the windshield wiper motor and link assembly with the 3 bolts as shown in the illustration.

Torque:

7.0 N·m {71 kgf·cm, 62 in·lbf}

(b) Connect the connector.

3. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

(a) Engage the 13 claws and install the cowl top ventilator louver sub-assembly as shown in the illustration.

(b) Install the 2 clips.

4. INSTALL FRONT FENDER TO COWL SIDE SEAL LH

(a) Engage the claw and 2 guides to install the front fender to cowl side seal LH.

5. INSTALL FRONT FENDER TO COWL SIDE SEAL RH

HINT:

Use the same procedure for the RH side and LH side.

6. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH

(a) Operate the wiper and stop the windshield wiper motor at the automatic stop position.

(b) When reusing the front wiper arm and blade assembly RH:

(1) Clean the wiper arm serrations.

Text in Illustration

*1	Wiper Arm Serration

(1) Clean the wiper pivot serrations with a wire brush.

Text in Illustration

*1	Wire Brush
*2	Wiper Pivot Serration

(d) Install the front wiper arm and blade assembly RH with the nut to the position shown in the illustration.

Text in Illustration

*1	Ceramic Notch

Torque:

20 N·m {204 kgf·cm, 15 ft·lbf}

7. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH

(a) When reusing the front wiper arm and blade assembly LH:

(1) Clean the wiper arm serrations.

Text in Illustration

*1	Wiper Arm Serration

(b) When reusing the windshield wiper link assembly:

(1) Clean the wiper pivot serrations with a wire brush.

Text in Illustration

*1	Wire Brush
*2	Wiper Pivot Serration

Text in Illustration

*1	Ceramic Notch

Torque:

20 N·m {204 kgf·cm, 15 ft·lbf}

(d) Operate the front wipers while spraying washer fluid onto the windshield. Make sure that the front wipers function properly and the wipers do not come into contact with the vehicle body.

8. INSTALL FRONT WIPER ARM HEAD CAP

(a) Install the 2 front wiper arm head caps.

Removal

REMOVAL PROCEDURE 1. REMOVE FRONT WIPER ARM HEAD CAP (a) Using a screwdriver, remove the 2 front wiper arm head caps as shown in the illustration. Text in Illustration ...

Front Wiper Rubber

Components COMPONENTS ILLUSTRATION Replacement REPLACEMENT PROCEDURE 1. REMOVE FRONT WIPER BLADE (a) Remove the holder of the front wiper blade. ...

Other materials about Toyota Venza:

Installation
INSTALLATION PROCEDURE 1. INSTALL REAR SEAT ASSEMBLY RH (a) Place the rear seat assembly RH in the cabin. NOTICE: Be careful not to damage the vehicle body. (b) Temporarily install the 2 bolts on the front side of the seat. ...

Camshaft Position "B" Actuator Circuit / Open (Bank 1) (P0013)
DESCRIPTION The Variable Valve Timing (VVT) system adjusts the exhaust valve timing to improve driveability. The engine oil pressure turns the VVT controller to adjust the valve timing. The camshaft timing oil control valve is a solenoid valve and switch ...

Malfunction in Deceleration Sensor (C1245/93)
DESCRIPTION If a malfunction in the deceleration sensor circuit occurs, the AWD control ECU will output this DTC. DTC No. DTC Detecting Condition Trouble Area C1296/96 When the following conditio ...