Toyota Venza: Installation

Toyota Venza Service Manual / Exterior Panels / Trim / Roof Drip Side Finish Moulding / Installation

INSTALLATION

PROCEDURE

1. INSTALL ROOF DRIP SIDE FINISH MOULDING CLIP (w/o Sliding Roof)

NOTICE:

If reusing the clips, do not remove the double-sided tape remaining on the clips and where the clips will be installed on the body.
If installing new clips, remove the double-sided tape remaining where the clips will be installed on the body and clean the body with a non-residue solvent.

(a) Apply a 2 to 3 mm (0.0787 to 0.118 in.) bead of adhesive (3M DP-105 or equivalent) to new roof drip side finish moulding clips.

HINT:

Adhesive strength (tensile strength): 13.7 MPa (140 kgf/cm2) or more (when the temperature is 23°C (73°F).)

(b) Press and install the 2 roof drip side finish moulding clips.

(c) Install the clips to the positions on the roof panel shown in the illustration. Determine the locations and firmly press and install the 2 roof drip side finish moulding clips after lightly applying adhesive (3M DP-105 or equivalent).

Standard Dimension

Item	Dimension
A	4.4 mm (0.173 in.)
B	10.2 mm (0.402 in.)
C	2.1 mm (0.0827 in.)
D	3.0 mm (0.118 in.)
E	3.0 mm (0.118 in.)
F	5.7 mm (0.224 in.)
G	10.4 mm (0.409 in.)

(d) Install the roof drip center side finish moulding when 20 minutes or more have elapsed after pressing and installing the 2 roof drip side finish moulding clips.

HINT:

Initial hardening time: 20 minutes
Complete hardening time: 48 hours

2. INSTALL ROOF DRIP CENTER SIDE FINISH MOULDING (w/o Sliding Roof)

(a) Engage the 2 clips and install the roof drip center side finish moulding as shown in the illustration.

3. INSTALL ROOF DRIP SIDE FINISH MOULDING CLIP (w/ Sliding Roof)

NOTICE:

If reusing the clips, do not remove the double-sided tape remaining on the clips and where the clips will be installed on the body.
If installing new clips, remove the double-sided tape remaining where the clips will be installed on the body and clean the body with a non-residue solvent.

(a) Apply a 2 to 3 mm (0.0787 to 0.118 in.) bead of adhesive (3M DP-105 or equivalent) to new roof drip side finish moulding clips.

HINT:

Adhesive strength (tensile strength): 13.7 MPa (140 kgf/cm2) or more (when the temperature is 23°C (73°F).)

(b) Press and install the 2 roof drip side finish moulding clips.

Standard Dimension

Item	Dimension
A	4.9 mm (0.193 in.)
B	8.4 mm (0.331 in.)
C	2.1 mm (0.0827 in.)
D	3.0 mm (0.118 in.)
E	3.0 mm (0.118 in.)
F	5.6 mm (0.221 in.)
G	10.4 mm (0.409 in.)

(d) Install the roof drip center side finish moulding when 20 minutes or more have elapsed after pressing and installing the 2 roof drip side finish moulding clips.

HINT:

Initial hardening time: 20 minutes
Complete hardening time: 48 hours

4. INSTALL ROOF DRIP CENTER SIDE FINISH MOULDING (w/ Sliding Roof)

(a) Engage the 2 clips and install the roof drip center side finish moulding as shown in the illustration.

Removal

REMOVAL PROCEDURE 1. REMOVE ROOF DRIP CENTER SIDE FINISH MOULDING (w/o Sliding Roof) (a) Put protective tape around the roof drip center side finish moulding. Text in Illustration ...

Side Mudguard

...

Other materials about Toyota Venza:

Poor Sound Quality in All Modes (Low Volume)
PROCEDURE 1. CHECK AUDIO SETTINGS (a) Set treble, middle and bass to the initial values and check that the sound is normal. OK: The sound returns to normal. HINT: Sound quality adjustment measures vary according to the ...

PIG Power Supply Voltage Malfunction (C1552)
DESCRIPTION When a problem occurs in the power steering system, the power source relay circuit is shut off to stop the power assist. DTC No. DTC Detection Condition Trouble Area C1552 PIG power s ...

Precaution
PRECAUTION NOTICE: When disconnecting the cable from the negative (-) battery terminal, initialize the following systems after the cable is reconnected. System Name See Procedure Back Door Closer System ...