Toyota Venza: Installation

Toyota Venza Service Manual / Tire Pressure Monitoring / Tire Pressure Warning Valve / Installation

INSTALLATION

CAUTION / NOTICE / HINT

NOTICE:

Always use a new grommet and valve core when installing the tire pressure warning valve and transmitter.
Check that the washer and nut are not damaged, and replace them if necessary.
Write down the ID number before installation.
Check that there is no oil, water or lubricant around the rim hole, tire pressure warning valve and transmitter, washer and nut. Failing to do so may result in improper installation.
Use only a specified tire valve cap. If an unspecified tire valve cap is used, it may seize to the tire pressure warning valve and transmitter.

PROCEDURE

1. INSTALL TIRE PRESSURE WARNING VALVE AND TRANSMITTER

(a) Install a new grommet to the tire pressure warning valve and transmitter.

NOTICE:

A new tire pressure warning valve and transmitter comes with a grommet installed. Make sure not to install an extra grommet.

(b) Write down the 7-digit transmitter ID number as shown in the illustration.

Text in Illustration

*a	Printed Surface
*b	7-digit Transmitter ID Number

NOTICE:

Make sure that the tire pressure warning valve and transmitter is installed so that the printed surface can be seen. If the tire pressure warning valve and transmitter is installed upside down, it may be damaged or fail to transmit signals when driving at high speeds.
Check that there is no deformation or damage to the tire pressure warning valve and transmitter.
Check that there is no foreign matter on the grommet and around the rim hole.

(d) From the outside of the rim, install the washer to the tire pressure warning valve and transmitter, and tighten the nut.

Text in Illustration

*1	Tire Pressure Warning Valve and Transmitter
*2	Grommet
*3	Washer
*4	Nut
*a	Rim

Torque:

4.0 N·m {41 kgf·cm, 35 in·lbf}

NOTICE:

No further tightening is required once the nut is tightened to the specified torque.
Check that there is no foreign matter on the grommet, washer and nut.

(e) Set the tire and disc wheel onto the mounting machine as shown in the illustration.

Text in Illustration

*a	Rim
*b	Mount Tool of the Mounting Machine
*c	60°
	Rim Rotating Direction
	Area for Tire Pressure Warning Valve and Transmitter

NOTICE:

Position the main body of the tire pressure warning valve and transmitter in the area shown in the illustration.
If the tire pressure warning valve and transmitter is positioned outside this area, it will interfere with the tire bead and may be damaged.

(f) Apply a sufficient coat of soapy water or equivalent to the tire bead and rim.

NOTICE:

Do not apply soapy water or equivalent directly to the tire pressure warning valve and transmitter.

(g) Using a mounting machine, install the tire to the disc wheel.

NOTICE:

Make sure that the tire bead and mount tool do not interfere with the tire pressure warning valve and transmitter.
Make sure that the tire pressure warning valve and transmitter is not clamped by the bead and rim.

(h) Install a new valve core.

(i) Retighten the nut to the specified torque.

Torque:

4.0 N·m {41 kgf·cm, 35 in·lbf}

NOTICE:

No further tightening is required once the nut is tightened to the specified torque.

(j) Check the surroundings of the tire pressure warning valve and transmitter for air leaks with soapy water or equivalent.

(1) If air is leaking from the valve core, press the valve core several times to remove foreign matter. Replace the valve core as necessary.

(2) If air is leaking from around the tire pressure warning valve and transmitter, check if the grommet, washer and nut are not deformed, damaged or contaminated with foreign matter. Replace the grommet, washer or nut as necessary.

(k) Install the tire valve cap.

2. INSTALL WHEEL ASSEMBLY

Torque:

103 N·m {1050 kgf·cm, 76 ft·lbf}

3. INSPECT TIRES

4. REGISTER TRANSMITTER ID

(See page )

5. INSPECT TIRE PRESSURE WARNING SYSTEM

(See page )

Removal

REMOVAL PROCEDURE 1. REMOVE WHEEL ASSEMBLY 2. REMOVE TIRE PRESSURE WARNING VALVE AND TRANSMITTER (a) Remove the tire valve cap. NOTICE: Keep the removed tire valve cap. (b) Remove the valve cor ...

Disposal

DISPOSAL CAUTION / NOTICE / HINT HINT: The tire pressure warning valve and transmitter is powered by a lithium battery. When disposing of the tire pressure warning valve and transmitter, remove t ...

Other materials about Toyota Venza:

Camshaft Position "B" Actuator Circuit / Open (Bank 1) (P0013)
DESCRIPTION The Variable Valve Timing (VVT) system adjusts the exhaust valve timing to improve driveability. The engine oil pressure turns the VVT controller to adjust the valve timing. The camshaft timing oil control valve is a solenoid valve and switch ...

Precaution
PRECAUTION 1. PRECAUTION FOR DISCONNECTING CABLE FROM NEGATIVE BATTERY TERMINAL NOTICE: When disconnecting the cable from the negative (-) battery terminal, initialize the following system after the terminal is reconnected: System Name ...

Noise Occurs
PROCEDURE 1. CHECK NOISE CONDITION (a) Check from which direction the noise comes (front left or right, or rear left or right). OK: The location of the noise source can be determined. NG GO TO STEP 3 ...