INSTALLATION
PROCEDURE
1. TEMPORARILY INSTALL REAR STABILIZER BAR BRACKET LH (for Front Side)
(a) Temporarily install the rear stabilizer bar bracket LH (front side) with the bolt. HINT: Loosely tighten the bolt so that the bracket can be moved by hand. |
|
2. TEMPORARILY INSTALL REAR STABILIZER BAR BRACKET RH (for Front Side)
(a) Temporarily install the rear stabilizer bar bracket RH (front side) with the 2 bolts. HINT: Loosely tighten the bolts so that the bracket can be moved by hand. |
|
3. INSTALL REAR STABILIZER BUSHING (for LH Side)
(a) Install the rear stabilizer bushing (LH side) to the rear stabilizer bar. NOTICE: Make sure that the cutout of the rear stabilizer bushing is positioned within the range shown in the illustration. |
|
4. INSTALL REAR STABILIZER BUSHING (for RH Side)
(a) Install the rear stabilizer bushing (RH side) to the rear stabilizer bar. NOTICE: Make sure that the cutout of the rear stabilizer bushing is positioned within the range shown in the illustration. |
|
5. INSTALL REAR STABILIZER BAR BRACKET LH (for Rear Side)
(a) Install the rear stabilizer bar bracket LH (rear side) with the 2 bolts. Torque: 19 N·m {194 kgf·cm, 14 ft·lbf} |
|
6. INSTALL REAR STABILIZER BAR BRACKET RH (for Rear Side)
(a) Install the rear stabilizer bar bracket RH (rear side) with the 2 bolts. Torque: 19 N·m {194 kgf·cm, 14 ft·lbf} |
|
7. FULLY TIGHTEN REAR STABILIZER BAR BRACKET LH (for Front Side)
(a) Fully tighten the bolt. Torque: 54 N·m {551 kgf·cm, 40 ft·lbf} |
|
8. FULLY TIGHTEN REAR STABILIZER BAR BRACKET RH (for Front Side)
(a) Fully tighten the 2 bolts. Torque: 19 N·m {194 kgf·cm, 14 ft·lbf} |
|
9. INSTALL REAR LOWER SUSPENSION BRACE (for LH Side)
(a) Install the rear lower suspension brace with the bolt and the nut. Torque: 35 N·m {357 kgf·cm, 26 ft·lbf} |
|
10. INSTALL REAR LOWER SUSPENSION BRACE (for RH Side)
HINT:
Perform the same procedure as the LH side.
11. INSTALL NO. 1 FLOOR UNDER COVER
12. INSTALL REAR STABILIZER LINK ASSEMBLY LH
(a) Install the rear stabilizer link assembly LH to the rear shock absorber with coil spring LH with the nut. Text in Illustration
Torque: 39 N·m {400 kgf·cm, 29 ft·lbf} HINT: If the ball joint turns together with the nut, use a hexagon wrench (5 mm) to hold the stud bolt. |
|
(b) Install the rear stabilizer link assembly LH to the rear stabilizer bar with the nut. Text in Illustration
Torque: 39 N·m {400 kgf·cm, 29 ft·lbf} HINT: If the ball joint turns together with the nut, use a hexagon wrench (5 mm) to hold the stud bolt. |
|
13. INSTALL REAR STABILIZER LINK ASSEMBLY RH
HINT:
Perform the same procedure as the LH side.
14. INSTALL REAR WHEELS
Torque:
103 N·m {1050 kgf·cm, 76 ft·lbf}
XM Tuner Malfunction (B15BA)
DESCRIPTION
These DTCs are stored when a malfunction occurs in the stereo component tuner
assembly.
DTC No.
DTC Detection Condition
Trouble Area
B15BA
When either of the following conditions is m ...
Headlight Leveling Ecu
Components
COMPONENTS
ILLUSTRATION
Removal
REMOVAL
PROCEDURE
1. REMOVE HEADLIGHT LEVELING ECU ASSEMBLY
(a) Disconnect the connector.
(b) Remove the bolt and headlight leveling ECU assembly ...
Relay
On-vehicle Inspection
ON-VEHICLE INSPECTION
PROCEDURE
1. INSPECT IG2 RELAY
(a) Remove the IG2 relay from the relay block.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Te ...