Toyota Venza manuals

Toyota Venza: Installation

INSTALLATION

PROCEDURE

1. INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY LH

(a) Temporarily install the rear No. 1 suspension arm assembly LH to the rear suspension member with the bolt and the nut.

Text in Illustration

*1

Identification Mark

NOTICE:

  • Ensure that the identification mark faces the rear side of the vehicle.
  • Since a stopper nut is used, temporarily tighten the bolt.

(b) Set the rear No. 1 suspension arm assembly LH in the tightening position shown in the illustration.

Standard angle (A):

7°36' (7.6°)

Standard length (B):

49.7 mm (1.96 in.)


(c) Fully tighten the bolt in the tightening position.

Torque:

80 N·m {816 kgf·cm, 59 ft·lbf}

NOTICE:

Since a stopper nut is used, fully tighten the bolt.


2. INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY RH

HINT:

Perform the same procedure as the LH side.

3. INSTALL REAR SUSPENSION MEMBER

(a) Raise the rear suspension member with a jack.

(b) Temporarily install the rear suspension member, 2 rear upper suspension member stoppers and 2 rear lower suspension member stopper retainers with the 4 nuts and 2 bolts.


NOTICE:

Be sure to install the rear suspension member with the rear upper suspension member stopper and the rear lower suspension member stopper retainer in the correct direction as shown in the illustration.

(c) Fully tighten the 2 nuts (A).

Torque:

115 N·m {1173 kgf·cm, 85 ft·lbf}

(d) Using SST and a socket wrench (19 mm), fully tighten the 2 nuts (B).

Text in Illustration

*1

Torque Wrench Fulcrum Length

*2

Turn

*3

Hold

SST: 09961-00950

Torque:

Specified Tightening Torque :

96 N·m {979 kgf·cm, 71 ft·lbf}

NOTICE:

This torque value is effective when SST is parallel to the torque wrench.

HINT:

  • Calculate the torque wrench reading when changing the fulcrum length for the torque wrench (See page ).

  • When using SST (fulcrum length of 150 mm (5.91 in.)) + torque wrench (fulcrum length of 425 mm (1.39 ft.)):

    71 N*m (724 kgf*cm, 52 ft.*lbf)


4. CONNECT REAR NO. 1 SUSPENSION ARM ASSEMBLY LH

(a) Connect the rear No. 1 suspension arm assembly LH to the rear axle carrier sub-assembly LH with the bolt and the nut.

Torque:

112 N·m {1142 kgf·cm, 83 ft·lbf}

NOTICE:

Since a stopper nut is used, temporarily tighten the bolt.


5. CONNECT REAR NO. 1 SUSPENSION ARM ASSEMBLY RH

HINT:

Perform the same procedure as the LH side.

6. INSTALL FRAME WIRE

(a) Engage the 2 clamps to install the frame wire.

NOTICE:

Do not twist the frame wire when installing it.


7. INSTALL NO. 3 FLOOR WIRE (w/ HID Headlight System)

(a) Engage the clamp and connect the connector to install the No. 3 floor wire.

NOTICE:

Do not twist the No. 3 floor wire when installing it.


8. INSTALL NO. 1 FLOOR UNDER COVER

(a) Install the No. 1 floor under cover with the 5 clips.


9. TEMPORARILY TIGHTEN REAR NO. 2 SUSPENSION ARM ASSEMBLY LH

(a) Temporarily tighten the rear No. 2 suspension arm assembly LH to the rear suspension member with the rear suspension toe adjust cam sub-assembly, the No. 2 camber adjust cam and the nut (B).

Text in Illustration

*1

Identification Mark

*2

Rear Suspension Toe Adjust Cam Sub-assembly

*3

No. 2 Camber Adjust Cam

NOTICE:

Ensure that the identification mark faces the rear side of the vehicle.

HINT:

When temporarily tightening the nut, keep the rear suspension toe adjust cam sub-assembly from rotating.


(b) Fully tighten the rear No. 2 suspension arm assembly LH to the rear axle carrier sub-assembly LH with the bolt (A) and the nut.

Torque:

112 N·m {1142 kgf·cm, 83 ft·lbf}

NOTICE:

Since a stopper nut is used, fully tighten the bolt.

10. TEMPORARILY TIGHTEN REAR NO. 2 SUSPENSION ARM ASSEMBLY RH

HINT:

Perform the same procedure as the LH side.

11. CONNECT REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY (w/ HID Headlight System)

(a) Connect the rear height control sensor sub-assembly to the rear No. 2 suspension arm assembly RH with the nut.

Torque:

5.4 N·m {55 kgf·cm, 48 in·lbf}


12. INSTALL REAR STRUT ROD ASSEMBLY LH


13. INSTALL REAR STRUT ROD ASSEMBLY RH

HINT:

Perform the same procedure as the LH side.

14. INSTALL NO. 3 PARKING BRAKE CABLE ASSEMBLY


15. INSTALL NO. 2 PARKING BRAKE CABLE ASSEMBLY


16. TEMPORARILY TIGHTEN PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY


17. FULLY TIGHTEN PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY


18. INSPECT AND ADJUST TRANSFER OIL

(a) Inspect and adjust the transfer oil (See page ).


19. INSTALL CENTER EXHAUST PIPE ASSEMBLY

(a) Install the center exhaust pipe assembly.

HINT:

Refer to the instructions for Installation of the exhaust pipe (See page for 2GR-FE,
for 1AR-FE).

20. INSPECT FOR EXHAUST GAS LEAK

21. INSTALL REAR WHEELS

Torque:

103 N·m {1050 kgf·cm, 76 ft·lbf}

22. STABILIZE SUSPENSION

(a) Lower the vehicle to the ground.

(b) Bounce the vehicle up and down at the corners to stabilize the rear suspension.

23. FULLY TIGHTEN REAR NO. 2 SUSPENSION ARM ASSEMBLY LH

(a) Align the matchmarks on the adjust cams and rear suspension member sub-assembly.

Text in Illustration

*1

Matchmark


(b) Fully tighten the nut.

Torque:

100 N·m {1020 kgf·cm, 74 ft·lbf}

NOTICE:

The final torque must be applied under standard vehicle height conditions.

HINT:

When fully tightening the nut, keep the rear suspension toe adjust cam sub-assembly from rotating.

24. FULLY TIGHTEN REAR NO. 2 SUSPENSION ARM ASSEMBLY RH

HINT:

Perform the same procedure as the LH side.

25. INSPECT AND ADJUST REAR WHEEL ALIGNMENT

(a) Inspect and adjust the rear wheel alignment (See page ).


26. HEIGHT CONTROL SENSOR SIGNAL INITIALIZATION (w/ HID Headlight System)

(a) Initialize the height control sensor signal (See page ).


27. INSPECT AND ADJUST HEADLIGHT AIMING (w/ HID Headlight System)

(a) Inspect and adjust the headlight aiming (See page ).


Components
COMPONENTS ILLUSTRATION ILLUSTRATION ILLUSTRATION ...

Removal
REMOVAL PROCEDURE 1. REMOVE REAR WHEELS 2. REMOVE CENTER EXHAUST PIPE ASSEMBLY (a) Remove the center exhaust pipe assembly. HINT: Refer to the instructions for Removal of the exhaust pipe (See p ...

Other materials about Toyota Venza:

Inspection
INSPECTION PROCEDURE 1. INSPECT FRONT NO. 2 SPEAKER ASSEMBLY (for 6 Speakers) (a) With the speaker installed, check that there is no looseness or other abnormalities. (b) Check that there is no foreign matter in the speaker, no tears on the speaker cone ...

Terminals Of Ecu
TERMINALS OF ECU 1. CHECK ENGINE SWITCH (a) Disconnect the D13 engine switch connector. (b) Measure the resistance according to the value(s) in the table below. HINT: Measure the values on the wire harness side with connector disconnected. T ...

Problem Symptoms Table
PROBLEM SYMPTOMS TABLE HINT: Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of probability in the "Suspected Area" ...

© 2016-2024 Copyright www.tovenza.com

0.17