Toyota Venza: Installation

Toyota Venza Service Manual / 1ar-fe Intake / Exhaust / Intake Manifold / Installation

INSTALLATION

PROCEDURE

1. INSTALL ENGINE MOUNTING DAMPER

(a) Install the engine mounting damper with the 3 bolts.

Torque:

9.0 N·m {92 kgf·cm, 80 in·lbf}

2. INSTALL WIRING HARNESS CLAMP BRACKET

(a) Install the bracket with the bolt.

Torque:

8.4 N·m {86 kgf·cm, 74 in·lbf}

3. INSTALL CHECK VALVE

(a) Connect the 2 vacuum hoses to the intake manifold to install the check valve.

(b) Check that the check valve is installed as shown in the illustration.

Text in Illustration

Black

4. INSTALL INTAKE MANIFOLD

(a) Close the tumble control valves.

NOTICE:

The tumble control valves may be damaged if they are not closed before installing the intake manifold.

HINT:

Connect the battery to the terminals of the actuator to operate the motor and close the valves (See page ).

(b) Install a new gasket to the intake manifold.

Torque:

28 N·m {286 kgf·cm, 21 ft·lbf}

(d) Connect the intake air control actuator connector.

(e) Attach the 2 clamps to the intake manifold and bracket.

(f) Install the wire harness with the bolt.

Torque:

8.4 N·m {86 kgf·cm, 74 in·lbf}

(g) Install the wire harness bracket with the bolt.

Torque:

8.4 N·m {86 kgf·cm, 74 in·lbf}

(h) Connect the fuel vapor feed hose, clamp and connector.

(i) Install the 2 wire harness brackets with the 2 bolts.

Torque:

8.4 N·m {86 kgf·cm, 74 in·lbf}

5. INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY

6. INSTALL UNION TO CONNECTOR TUBE HOSE

(a) Install the union to connector tube hose to the intake manifold.

7. CONNECT NO. 2 VENTILATION HOSE

(a) Connect the No. 2 ventilation hose to the intake manifold.

8. INSTALL VACUUM SWITCHING VALVE ASSEMBLY (for ACIS)

(a) Install the vacuum switching valve (for ACIS) with the bolt.

Torque:

9.0 N·m {92 kgf·cm, 80 in·lbf}

(b) Connect the 2 vacuum hoses, 2 union to connector tube hoses, clamp and connector.

9. INSTALL THROTTLE BODY ASSEMBLY

(a) Install the throttle body assembly (See page ).

10. CONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page ).

11. INSPECT FOR FUEL LEAK

HINT:

(See page ).

Inspection

INSPECTION PROCEDURE 1. INSPECT INTAKE AIR CONTROL VALVE (for ACIS) (a) Inspect the diaphragm. (1) Using a vacuum pump, apply a vacuum of 60 kPa (450 mmHg, 17.7 in.Hg) or higher to ...

Intake System

Parts Location PARTS LOCATION ILLUSTRATION System Diagram SYSTEM DIAGRAM On-vehicle Inspection ON-VEHICLE INSPECTION PROCEDURE 1. INSPECT INTAKE SYSTEM HINT: Perform "Inspec ...

Other materials about Toyota Venza:

All Door Entry Lock/Unlock Functions do not Operate, but Wireless Functions Operate
DESCRIPTION When the wireless door lock and unlock functions operate, the communication circuit between the door lock receiver assembly and certification ECU (smart key ECU assembly) is normal. When the entry lock and unlock functions do not operate, radi ...

Diagnostic Trouble Code Chart
DIAGNOSTIC TROUBLE CODE CHART CAN Communication System DTC Code Detection Item Output ECU/Techstream Display See page U0100 Lost Communication with ECM / PCM Power management ...

LIN Communication Master Malfunction (B2287)
DESCRIPTION This DTC is stored when there is an open, short or ECU communication malfunction between the power management control ECU and certification ECU (smart key ECU assembly). DTC No. DTC Detection Condition Trouble A ...