INSTALLATION
PROCEDURE
1. INSTALL NO. 1 MANIFOLD CONVERTER INSULATOR
(a) Install the No. 1 manifold converter insulator to the exhaust manifold converter sub-assembly with the 4 bolts. Torque: 12 N·m {122 kgf·cm, 9 ft·lbf} |
|
2. INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR
(a) Install the No. 2 exhaust manifold heat insulator to the exhaust manifold converter sub-assembly with the 2 bolts. Torque: 12 N·m {122 kgf·cm, 9 ft·lbf} |
|
3. INSTALL EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY
(a) Install a new gasket onto the cylinder head sub-assembly. |
|
(b) Temporarily install the exhaust manifold converter sub-assembly to the cylinder head sub-assembly with the 5 nuts. |
|
(c) Tighten the 5 nuts in the order shown in the illustration.
Torque:
35 N·m {357 kgf·cm, 26 ft·lbf}
4. INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR
(a) Install the No. 1 exhaust manifold heat insulator to the exhaust manifold converter sub-assembly with the 4 bolts. Torque: 12 N·m {122 kgf·cm, 9 ft·lbf} |
|
5. INSTALL NO. 2 MANIFOLD STAY
(a) Install the No. 2 manifold stay to the exhaust manifold converter sub-assembly and stiffening crankcase assembly with the bolt and nut. Torque: 43 N·m {438 kgf·cm, 32 ft·lbf} |
|
6. INSTALL MANIFOLD STAY
(a) Install the manifold stay to the exhaust manifold converter sub-assembly and stiffening crankcase assembly with the bolt and nut. Torque: 43 N·m {438 kgf·cm, 32 ft·lbf} |
|
7. INSTALL AIR FUEL RATIO SENSOR
8. INSTALL FRONT EXHAUST PIPE ASSEMBLY
(a) Using a vernier caliper, measure the free length of the compression spring. Minimum Free Length: 41.5 mm (1.63 in.) If the length is less than the minimum, replace the compression spring. |
|
(b) Temporarily install a new gasket to the exhaust manifold converter sub-assembly.
(c) Using a plastic hammer and wooden block, tap in the gasket until its surface is flush with the exhaust manifold converter sub-assembly. Text in Illustration
NOTICE:
|
|
(d) Install a new gasket to the center exhaust pipe assembly.
(e) Install the front exhaust pipe assembly to the exhaust manifold converter sub-assembly and center exhaust pipe assembly with the 2 compression springs and 4 bolts. Torque: 43 N·m {438 kgf·cm, 32 ft·lbf} |
|
(f) Connect the heated oxygen sensor connector. |
|
9. INSPECT FOR EXHAUST GAS LEAK
10. INSTALL NO. 2 ENGINE UNDER COVER
11. INSTALL NO. 1 ENGINE UNDER COVER
Brake Warning Light does not Come ON
DESCRIPTION
The skid control ECU is connected to the combination meter via CAN communication.
WIRING DIAGRAM
Refer to Brake Warning Light Remains ON (See page
).
PROCEDURE
1.
CHECK CAN COMMUNICATION SYSTEM
(a) Check if a ...
Parts Location
PARTS LOCATION
ILLUSTRATION
ILLUSTRATION
ILLUSTRATION
ILLUSTRATION
ILLUSTRATION
...
Sleep Operation Failure of Occupant Classification ECU (B1796)
DESCRIPTION
In sleep mode, the occupant classification ECU reads the condition of each sensor
while the ignition switch is off.
In this mode, if occupant classification ECU detects an internal malfunction,
DTC B1796 is output.
DTC No.
...