INSTALLATION
PROCEDURE
1. INSTALL NO. 1 FUEL TANK CUSHION
(a) Install 8 new No. 1 fuel tank cushions to the fuel tank. |
|
2. INSTALL FUEL MAIN TUBE SUPPORT
(a) Install the fuel main tube support with the bolt. Torque: 5.4 N·m {55 kgf·cm, 48 in·lbf} |
|
3. INSTALL FUEL TANK MAIN TUBE SUB-ASSEMBLY
(a) Install the fuel tank main tube to the fuel main tube support. |
|
4. INSTALL FUEL TANK TO FILLER PIPE HOSE
(a) Install the fuel tank to filler pipe hose to the fuel tank assembly with the clamp. |
|
5. INSTALL FUEL TANK VENT HOSE SUB-ASSEMBLY
(a) Install the fuel tank vent hose sub-assembly. |
|
6. INSTALL FUEL SENDER GAUGE ASSEMBLY
7. INSTALL FUEL TANK ASSEMBLY
(a) Install the 4 clip nuts. |
|
(b) Install the 2 fuel tank bands with the 2 pins. |
|
(c) Set the fuel tank assembly onto the engine lifter.
(d) Lift up the engine lifter. NOTICE: Slowly raise the lifter so as to not drop the fuel tank assembly. |
|
(e) Install the fuel tank assembly with the fuel tank bands and 2 bolts. Torque: 45 N·m {459 kgf·cm, 33 ft·lbf} |
|
(f) Connect the fuel tank to filler pipe hose with the clamp. |
|
(g) Connect the 2 clamps and install the fuel tank vent hose sub-assembly.
(h) Push in the tube connector to the pipe and push up the retainer to connect the fuel tank vent hose sub-assembly.
Text in Illustration
*1 |
Retainer |
Push Up |
NOTICE:
(i) Connect the fuel tank main tube sub-assembly. (1) Push in the fuel pump tube connector to the pipe and push up the retainer so that the claws engage. NOTICE:
|
|
8. INSTALL NO. 3 PARKING BRAKE CABLE ASSEMBLY
(a) Install the No. 3 parking brake cable assembly with the bolt and nut. Torque: 6.0 N·m {61 kgf·cm, 53 in·lbf} |
|
9. INSTALL NO. 2 PARKING BRAKE CABLE ASSEMBLY
(a) Install the No. 2 parking brake cable assembly with the bolt and nut. Torque: 6.0 N·m {61 kgf·cm, 53 in·lbf} |
|
10. INSTALL NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY
(a) Install the No. 1 fuel tank protector sub-assembly with the 4 bolts. Torque: 5.4 N·m {55 kgf·cm, 48 in·lbf} |
|
11. INSTALL FRONT FLOOR BRACE LH
(a) Install the bolt, 2 nuts and front floor brace LH.
Torque:
56 N·m {571 kgf·cm, 41 ft·lbf}
12. INSTALL FRONT FLOOR BRACE RH
(a) Install the bolt, 2 nuts and front floor brace RH.
Torque:
56 N·m {571 kgf·cm, 41 ft·lbf}
13. INSTALL ELECTRO MAGNETIC CONTROL COUPLING SUB-ASSEMBLY (for AWD)
14. INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for AWD)
(a) Install the propeller with center bearing shaft assembly (See page ).
15. INSTALL CENTER EXHAUST PIPE ASSEMBLY
HINT:
(See page ).
16. ADD FUEL
17. INSTALL REAR NO. 2 FLOOR SERVICE HOLE COVER
18. INSTALL FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE
(a) Install the fuel suction tube assembly with pump and gauge (See page ).
19. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page ).
20. INSPECT FOR EXHAUST GAS LEAK
Insufficient Coolant Temperature for Closed Loop Fuel Control (P0125)
DESCRIPTION
Refer to DTC P0115 (See page ).
DTC No.
DTC Detection Condition
Trouble Area
P0125
The engine coolant temperature does not reach the closed loop enabling
temperature for 20 minutes ...
Noise Occurs or Sound Skips when Portable Player Plays
CAUTION / NOTICE / HINT
HINT:
Perform this check with the portable player volume set at an appropriate
level.
Make sure that there are no obstructions between the portable player
and navigation receiver assembly that may block signals, an ...
Inspection
INSPECTION
PROCEDURE
1. INSPECT REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
(a) Apply positive (+) battery voltage to connector terminal 2 (B).
NOTICE:
Do not apply positive (+) battery voltage to any terminals other than
terminal 2 ( ...