Toyota Venza: Inspection

Toyota Venza Service Manual / U660e Automatic Transmission / Transaxle / Valve Body Assembly(when Not Using The Engine Support Bridge) / Inspection

INSPECTION

PROCEDURE

1. INSPECT SHIFT SOLENOID VALVE SL

(a) Measure the resistance according to the value(s) in the table below.

Text in Illustration

*1	Shift Solenoid Valve SL

Standard Resistance:

Tester Connection	Condition	Specified Condition
Solenoid Connector (SL) - Solenoid Body (SL)	20°C (68°F)	11 to 15 Ω

If the value is not as specified, replace the shift solenoid valve.

(b) Connect a positive (+) battery lead to the terminal of the solenoid connector, and a negative (-) battery lead to the solenoid body, and check the operation of the valve.

NOTICE:

When using battery voltage during the inspection, do not bring the positive (+) and negative (-) tester probes too close to each other as a short circuit may occur.

OK:

The valve moves and makes an operating sound.

If the operation cannot be done as specified, replace the shift solenoid valve.

2. INSPECT SHIFT SOLENOID VALVE SLT

(a) Measure the resistance according to the value(s) in the table below.

Text in Illustration

*1	Component without harness connected: (Shift Solenoid Valve SL)

Standard Resistance:

Tester Connection	Condition	Specified Condition
1 - 2	20°C (68°F)	5.0 to 5.6 Ω

If the value is not as specified, replace the shift solenoid valve.

(b) Connect a positive (+) battery lead with a 21 W bulb to terminal 2 and a negative (-) battery lead to terminal 1 of the solenoid valve connector, and check the operation of the valve.

NOTICE:

When using battery voltage during the inspection, do not bring the positive (+) and negative (-) tester probes too close to each other as a short circuit may occur.

OK:

The valve moves and makes an operating sound.

If the operation cannot be done as specified, replace the shift solenoid valve.

3. INSPECT SHIFT SOLENOID VALVE SLU

(a) Measure the resistance according to the value(s) in the table below.

Text in Illustration

*1	Component without harness connected: (Shift Solenoid Valve SLU)

Standard Resistance:

Tester Connection	Condition	Specified Condition
1 - 2	20°C (68°F)	5.0 to 5.6 Ω

If the value is not as specified, replace the shift solenoid valve.

(b) Connect a positive (+) battery lead with a 21 W bulb to terminal 2 and a negative (-) battery lead to terminal 1 of the solenoid valve connector, and check the operation of the valve.

NOTICE:

When using battery voltage during the inspection, do not bring the positive (+) and negative (-) tester probes too close to each other as a short circuit may occur.

OK:

The valve moves and makes an operating sound.

If the operation cannot be done as specified, replace the shift solenoid valve.

4. INSPECT SHIFT SOLENOID VALVE SL1

(a) Measure the resistance according to the value(s) in the table below.

Text in Illustration

*1	Component without harness connected: (Shift Solenoid Valve SL1)

Standard Resistance:

Tester Connection	Condition	Specified Condition
1 - 2	20°C (68°F)	5.0 to 5.6 Ω

If the value is not as specified, replace the shift solenoid valve.

(b) Connect a positive (+) battery lead with a 21 W bulb to terminal 2 and a negative (-) battery lead to terminal 1 of the solenoid valve connector, and check the operation of the valve.

NOTICE:

When using battery voltage during the inspection, do not bring the positive (+) and negative (-) tester probes too close to each other as a short circuit may occur.

OK:

The valve moves and makes an operating sound.

If the operation cannot be done as specified, replace the shift solenoid valve.

5. INSPECT SHIFT SOLENOID VALVE SL2

(a) Measure the resistance according to the value(s) in the table below.

Text in Illustration

*1	Component without harness connected: (Shift Solenoid Valve SL2)

Standard Resistance:

Tester Connection	Condition	Specified Condition
1 - 2	20°C (68°F)	5.0 to 5.6 Ω

If the value is not as specified, replace the shift solenoid valve.

(b) Connect a positive (+) battery lead with a 21 W bulb to terminal 2 and a negative (-) battery lead to terminal 1 of the solenoid valve connector, and check the operation of the valve.

NOTICE:

When using battery voltage during the inspection, do not bring the positive (+) and negative (-) tester probes too close to each other as a short circuit may occur.

OK:

The valve moves and makes an operating sound.

If the operation cannot be done as specified, replace the shift solenoid valve.

6. INSPECT SHIFT SOLENOID VALVE SL3

(a) Measure the resistance according to the value(s) in the table below.

Text in Illustration

*1	Component without harness connected: (Shift Solenoid Valve SL3)

Standard Resistance:

Tester Connection	Condition	Specified Condition
1 - 2	20°C (68°F)	5.0 to 5.6 Ω

If the value is not as specified, replace the shift solenoid valve.

(b) Connect a positive (+) battery lead with a 21 W bulb to terminal 2 and a negative (-) battery lead to terminal 1 of the solenoid valve connector, and check the operation of the valve.

NOTICE:

When using battery voltage during the inspection, do not bring the positive (+) and negative (-) tester probes too close to each other as a short circuit may occur.

OK:

The valve moves and makes an operating sound.

If the operation cannot be done as specified, replace the shift solenoid valve.

7. INSPECT SHIFT SOLENOID VALVE SL4

(a) Measure the resistance according to the value(s) in the table below.

Text in Illustration

*1	Component without harness connected: (Shift Solenoid Valve SL4)

Standard Resistance:

Tester Connection	Condition	Specified Condition
1 - 2	20°C (68°F)	5.0 to 5.6 Ω

If the value is not as specified, replace the shift solenoid valve.

(b) Connect a positive (+) battery lead with a 21 W bulb to terminal 2 and a negative (-) battery lead to terminal 1 of the solenoid valve connector, and check the operation of the valve.

NOTICE:

When using battery voltage during the inspection, do not bring the positive (+) and negative (-) tester probes too close to each other as a short circuit may occur.

OK:

The valve moves and makes an operating sound.

If the operation cannot be done as specified, replace the shift solenoid valve.

Removal

REMOVAL PROCEDURE 1. REMOVE AUTOMATIC TRANSAXLE ASSEMBLY HINT: See the steps from "Remove Engine Assembly with transaxle" through "Remove Automatic Transaxle Assembly" (See p ...

Reassembly

REASSEMBLY PROCEDURE 1. INSTALL SHIFT SOLENOID VALVE SL4 (a) Coat the shift solenoid valve SL4 and bolt with ATF. Text in Illustration *1 Lock Pla ...

Other materials about Toyota Venza:

Installation
INSTALLATION CAUTION / NOTICE / HINT HINT: Perform "Inspection After Repair" after replacing the engine assembly (See page ). PROCEDURE 1. INSTALL IGNITION COIL ASSEMBLY 2. INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY 3. INSTALL ENGINE COOL ...

Lost Communication with "Seat Control Module A" (U0208)
DESCRIPTION DTC No. DTC Detection Condition Trouble Area U0208 No communication from the position control ECU and switch assembly. Position control ECU and switch assembly bran ...

Removal
REMOVAL PROCEDURE 1. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY (w/o Seat Heater System) 2. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY (w/ Seat Heater System) 3. REMOVE NO. 2 CONSOLE BOX CARPET 4. REMOVE CONSOLE BOX ASSEMBLY 5. REMOVE AIR CONDITION ...