INSPECTION
PROCEDURE
1. INSPECT PRELOAD
(a) Using SST and a torque wrench, measure the preload of the backlash between the driven pinion and ring gear. SST: 09326-20011 Preload (at Starting):
HINT:
|
|
(b) Using SST and a torque wrench, measure the total preload.
SST: 09326-20011
Preload (at Starting):
Item |
Preload |
---|---|
without SST |
0.35 to 0.53 N*m (4 to 5 kgf*cm, 3 to 4 in.*lbf) + driven pinion preload |
with SST |
0.25 to 0.38 N*m (3 to 4 kgf*cm, 3 to 3.3 in.*lbf) + driven pinion preload |
HINT:
If the preload is outside the specified range, replace the No. 2 transfer ring gear mounting case washer with one that is thicker or thinner as necessary and recheck.
Text in Illustration
*1 |
No. 2 Transfer Ring Gear Mounting Case Washer |
Mark |
Thickness |
Mark |
Thickness |
---|---|---|---|
G7 |
2.47 (0.0972) |
M7 |
3.47 (0.1366) |
G8 |
2.49 (0.0980) |
M8 |
3.49 (0.1374) |
G9 |
2.51 (0.0988) |
M9 |
3.51 (0.1382) |
H0 |
2.53 (0.0996) |
N0 |
3.53 (0.1390) |
H1 |
2.55 (0.1004) |
N1 |
3.55 (0.1398) |
H2 |
2.57 (0.1012) |
N2 |
3.57 (0.1406) |
H3 |
2.59 (0.1020) |
N3 |
3.59 (0.1413) |
H4 |
2.61 (0.1028) |
N4 |
3.61 (0.1421) |
H5 |
2.63 (0.1035) |
N5 |
3.63 (0.1429) |
H6 |
2.65 (0.1043) |
N6 |
3.65 (0.1437) |
H7 |
2.67 (0.1051) |
N7 |
3.67 (0.1445) |
H8 |
2.69 (0.1059) |
N8 |
3.69 (0.1453) |
H9 |
2.71 (0.1067) |
N9 |
3.71 (0.1461) |
J0 |
2.73 (0.1075) |
P0 |
3.73 (0.1469) |
J1 |
2.75 (0.1083) |
P1 |
3.75 (0.1476) |
J2 |
2.77 (0.1091) |
P2 |
3.77 (0.1484) |
J3 |
2.79 (0.1098) |
P3 |
3.79 (0.1492) |
J4 |
2.81 (0.1106) |
P4 |
3.81 (0.1500) |
J5 |
2.83 (0.1114) |
P5 |
3.83 (0.1508) |
J6 |
2.85 (0.1122) |
P6 |
3.85 (0.1516) |
J7 |
2.87 (0.1130) |
P7 |
3.87 (0.1524) |
J8 |
2.89 (0.1138) |
P8 |
3.89 (0.1531) |
J9 |
2.91 (0.1146) |
P9 |
3.91 (0.1539) |
K0 |
2.93 (0.1154) |
Q0 |
3.93 (0.1547) |
K1 |
2.95 (0.1161) |
Q1 |
3.95 (0.1555) |
K2 |
2.97 (0.1169) |
Q2 |
3.97 (0.1563) |
K3 |
2.99 (0.1177) |
Q3 |
3.99 (0.1571) |
K4 |
3.01 (0.1185) |
Q4 |
4.01 (0.1579) |
K5 |
3.03 (0.1193) |
Q5 |
4.03 (0.1587) |
K6 |
3.05 (0.1201) |
Q6 |
4.05 (0.1594) |
K7 |
3.07 (0.1209) |
Q7 |
4.07 (0.1602) |
K8 |
3.09 (0.1217) |
Q8 |
4.09 (0.1610) |
K9 |
3.11 (0.1224) |
Q9 |
4.11 (0.1618) |
L0 |
3.13 (0.1232) |
R0 |
4.13 (0.1626) |
L1 |
3.15 (0.1240) |
R1 |
4.15 (0.1634) |
L2 |
3.17 (0.1248) |
R2 |
4.17 (0.1642) |
L3 |
3.19 (0.1256) |
R3 |
4.19 (0.1650) |
L4 |
3.21 (0.1264) |
R4 |
4.21 (0.1657) |
L5 |
3.23 (0.1272) |
R5 |
4.23 (0.1665) |
L6 |
3.25 (0.1280) |
R6 |
4.25 (0.1673) |
L7 |
3.27 (0.1287) |
R7 |
4.27 (0.1681) |
L8 |
3.29 (0.1295) |
R8 |
4.29 (0.1689) |
L9 |
3.31 (0.1303) |
R9 |
4.31 (0.1697) |
M0 |
3.33 (0.1311) |
S0 |
4.33 (0.1705) |
M1 |
3.35 (0.1319) |
S1 |
4.35 (0.1713) |
M2 |
3.37 (0.1327) |
S2 |
4.37 (0.1720) |
M3 |
3.39 (0.1335) |
S3 |
4.39 (0.1728) |
M4 |
3.41 (0.1343) |
S4 |
4.41 (0.1736) |
M5 |
3.43 (0.1350) |
S5 |
4.43 (0.1744) |
M6 |
3.45 (0.1358) |
S6 |
4.45 (0.1752) |
2. INSPECT RING GEAR BACKLASH
(a) Using a dial indicator, check the backlash of the ring gear. Backlash: 0.14 to 0.25 mm (0.00551 to 0.00984 in.) If the backlash is not within the specification, adjust the side bearing preload or repair as necessary. NOTICE: Check at least 3 positions on the circumference of the ring gear. |
|
3. INSPECT TOOTH CONTACT BETWEEN RING GEAR AND DRIVE PINION
(a) Coat 3 or 4 teeth at 4 different positions on the ring gear with Prussian blue. |
|
(b) Turn the driven pinion to rotate the ring gear 10 times or more clockwise and 10 times or more counterclockwise.
(c) Rotate the ring gear to inspect the tooth pattern.
(d) If the tooth contact pattern is not correct, select a new transfer output shaft washer that is thicker or thinner as necessary and recheck.
4. INSPECT RUNOUT OF RING GEAR
(a) Place the transfer ring gear mounting case on the V-blocks. |
|
(b) Using a dial indicator, check the runout of the ring gear.
Maximum runout:
0.06 mm (0.00236 in.)
HINT:
If the runout is more than maximum, replace the ring gear with a new one.
5. INSPECT TRANSFER RING GEAR MOUNTING CASE
(a) Place the transfer ring gear mounting case on the V-blocks. |
|
(b) Using a dial indicator, check the runout of the transfer ring gear mounting case.
Maximum runout:
0.04 mm (0.00157 in.)
HINT:
If the runout is more than maximum, replace the transfer ring gear mounting case with a new one.
Front seats
► Power seat
1. Seat position fore/aft control switch
2. Seatback angle control switch
3. Seat cushion (front) angle control switch (driver’s side only)
4. Vertical height control switch (driver’s side only)
5. Lumbar support control switch
& ...
Power windows
The power windows can be opened and closed using the following switches.
1. One-touch closing*
2. Closing
3. One-touch opening*
4. Opening
*:To stop the window partway, operate the switch in the opposite direction.
Lock switch
Press the switch down ...
Inspection
INSPECTION
PROCEDURE
1. INSPECT GENERATOR CLUTCH PULLEY
(a) Hold the generator rotor using SST, and turn the clutch pulley clockwise
to check that the outer ring locks.
SST: 09820-63021
Text in Illustration
*1
...