Toyota Venza: Inspection

Toyota Venza Service Manual / Supplemental Restraint Systems / Spiral Cable / Inspection

INSPECTION

PROCEDURE

1. INSPECT SPIRAL CABLE

(a) Visually check for defects with the spiral cable removed from the vehicle.

(1) The defects are as follows:

Scratches on the spiral cable
Small cracks the spiral cable
Dents on the spiral cable
Chips on the spiral cable
Cracks or other damage to the connector
OK:

No defects are found.

HINT:

If any of the defects is found, replace the spiral cable with a new one.

(b) Inspect the spiral cable.

Text in Illustration

Component without harness connected

(Spiral Cable)

Color: Orange

Color: Black

(1) Measure the resistance according to the value(s) in the table below.

NOTICE:

To avoid breakage of the spiral cable, do not turn the spiral cable more than necessary.

If the value is not within the specified range, replace the spiral cable.

Standard Resistance

Tester Connection	Condition	Specified Condition
z5-1 - D18-8 (HO)	Center	Below 1 Ω
	2.5 rotations to the left
	2.5 rotations to the right
z5-3 - D18-10 (-DP)	Center	Below 1 Ω
	2.5 rotations to the left
	2.5 rotations to the right
z5-5 - D18-12 (IL+2)	Center	Below 1 Ω
	2.5 rotations to the left
	2.5 rotations to the right
z5-7 - D18-3 (EAU)	Center	Below 1 Ω
	2.5 rotations to the left
	2.5 rotations to the right
z5-8 - D18-4 (AU3)	Center	Below 1 Ω
	2.5 rotations to the left
	2.5 rotations to the right
z5-9 - D18-5 (AU2)	Center	Below 1 Ω
	2.5 rotations to the left
	2.5 rotations to the right
z5-10 - D18-6 (AU1)	Center	Below 1 Ω
	2.5 rotations to the left
	2.5 rotations to the right
z6-3 - D18-1 (CCS)	Center	Below 1 Ω
	2.5 rotations to the left
	2.5 rotations to the right
z6-4 - D18-2 (ECC)	Center	Below 1 Ω
	2.5 rotations to the left
	2.5 rotations to the right
z1-1 - D7-2 (D-)	Center	Below 1 Ω
	2.5 rotations to the left
	2.5 rotations to the right
z1-2 - D7-1 (D+)	Center	Below 1 Ω
	2.5 rotations to the left
	2.5 rotations to the right
z2-1 - D7-3 (D2-)	Center	Below 1 Ω
	2.5 rotations to the left
	2.5 rotations to the right
z2-2 - D7-4 (D2+)	Center	Below 1 Ω
	2.5 rotations to the left
	2.5 rotations to the right

Removal

REMOVAL PROCEDURE 1. PRECAUTION CAUTION: Be sure to read Precaution thoroughly before servicing (See page ). 2. TURN FRONT WHEELS TO FACE STRAIGHT AHEAD 3. DISCONNECT CABLE FROM NEGATIVE BATTE ...

Other materials about Toyota Venza:

System Description
SYSTEM DESCRIPTION 1. OUTLINE OF THEFT DETERRENT SYSTEM The theft deterrent system can be set by locking the doors using the transmitter or key, or by opening and closing the doors (for details, refer to Active Arming Mode or Passive Arming Mo ...

Removal
REMOVAL PROCEDURE 1. REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY 2. REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Exhaust Side) (a) Disconnect the oil control valve connector. (b) Remove the ...

Evaporator Temperature Sensor Circuit (B1413/13)
DESCRIPTION The evaporator temperature sensor is installed on the evaporator in the air conditioning unit to detect the cooled air temperature that has passed through the evaporator and to control the air conditioning. It sends appropriate signals to the ...

Toyota Venza: Inspection

Components

Removal

Other materials about Toyota Venza: