Toyota Venza: Inspection

Toyota Venza Service Manual / Door Lock / Rear Door Lock / Inspection

INSPECTION

PROCEDURE

1. INSPECT REAR DOOR LOCK ASSEMBLY LH

(a) Check the operation of the door lock motor.

(1) Apply battery voltage and check the operation of the door lock motor.

OK:

Measurement Condition

Specified Condition

Battery positive (+) → Terminal 4 (DL)

Battery negative (-) → Terminal 1 (UL)

Locks

Battery positive (+) → Terminal 1 (UL)

Battery negative (-) → Terminal 4 (DL)

Unlocks

Text in Illustration

Component without harness connected

(Rear Door Lock Assembly LH)

Lock

Unlock

If the result is not as specified, replace the rear door lock assembly LH.

(b) Check the operation of the unlock detection switch.

(1) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection	Condition	Specified Condition
6 (LSSR) - 9 (E)	Locked	10 kΩ or higher
6 (LSSR) - 9 (E)	Unlocked	Below 1 Ω

Text in Illustration

Component without harness connected

(Rear Door Lock Assembly LH)

Lock

Unlock

If the result is not as specified, replace the rear door lock assembly LH.

2. INSPECT REAR DOOR LOCK ASSEMBLY RH

(a) Check the operation of the door lock motor.

(1) Apply battery voltage and check the operation of the door lock motor.

OK:

Measurement Condition

Specified Condition

Battery positive (+) → Terminal 4 (L)

Battery negative (-) → Terminal 1 (DL)

Locks

Battery positive (+) → Terminal 1 (DL)

Battery negative (-) → Terminal 4 (L)

Unlocks

Text in Illustration

Component without harness connected

(Rear Door Lock Assembly RH)

Lock

Unlock

If the result is not as specified, replace the rear door lock assembly RH.

(b) Check the operation of the unlock detection switch.

(1) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection	Condition	Specified Condition
6 (LSSR) - 9 (E)	Locked	10 kΩ or higher
6 (LSSR) - 9 (E)	Unlocked	Below 1 Ω

Text in Illustration

Component without harness connected

(Rear Door Lock Assembly RH)

Lock

Unlock

If the result is not as specified, replace the rear door lock assembly RH.

Removal

REMOVAL PROCEDURE 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL CAUTION: Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS sys ...

Installation

INSTALLATION PROCEDURE 1. INSTALL REAR DOOR LOCK ASSEMBLY NOTICE: When reusing the removed rear door lock assembly, replace the door lock wiring harness seal on the connector with a ne ...

Other materials about Toyota Venza:

Wireless-linked Return Function does not Operate
DESCRIPTION When a door is unlocked using the wireless unlock function or entry unlock function, the certification ECU (smart key ECU assembly) sends a door unlock signal and key ID signal to the main body ECU (driver side junction block assembly). When t ...

Short in Torque Converter Clutch Solenoid Circuit (Shift Solenoid Valve SL) (P2769,P2770)
DESCRIPTION Shift solenoid valve SL is turned on and off by signals from the TCM to control the hydraulic pressure acting on the lock-up relay valve, which then controls operation of the lock-up clutch. DTC No. DTC Detection Conditi ...

Torque Sensor Circuit Malfunction (C1511-C1514,C1517)
DESCRIPTION The torque sensor converts the rotation torque input to the steering wheel into an electrical signal and sends it to the power steering ECU. Based on this signal, the ECU detects steering effort. DTC No. DTC Detection Co ...