Toyota Venza: Inspection

Toyota Venza Service Manual / Window / Glass / Power Window Regulator Motor(for Rear Door) / Inspection

INSPECTION

PROCEDURE

1. INSPECT REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

(a) Apply positive (+) battery voltage to connector terminal 2 (B).

NOTICE:

Do not apply positive (+) battery voltage to any terminals other than terminal 2 (B) to avoid damaging the pulse sensor inside the motor.

(b) Connect a ground lead to connector terminals 1 (GND) and 7 (DOWN) or 10 (UP).

OK:

Measurement Condition	Specified Condition
Connect a positive (+) battery lead to terminal 2 (B), connect a negative (-) battery lead to terminal 1 (GND), and keep them connected for 3 seconds or more. With terminals 2 (B) and 1 (GND) connected, connect a negative (-) battery lead to terminal 10 (UP). Disconnect and reconnect a negative (-) battery lead to terminal 10 (UP) within 1 second.	Motor gear rotates clockwise (Up)
Connect a positive (+) battery lead to terminal 2 (B), connect a negative (-) battery lead to terminal 1 (GND), and keep them connected for 3 seconds or more. With terminals 2 (B) and 1 (GND) connected, connect a negative (-) battery lead to terminal 7 (DOWN). Disconnect and reconnect a negative (-) battery lead to terminal 7 (DOWN) within 1 second.	Motor gear rotates counterclockwise (Down)

Text in Illustration

*1	Component without harness connected (to Rear Power Window Regulator Motor Assembly LH)

If the result is not as specified, replace the rear power window regulator motor assembly LH.

CAUTION:

Reset the power window regulator motor (initialize the pulse sensor) after installing the power window regulator motor and regulator assembly onto the door.

2. INSPECT REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

(a) Apply positive (+) battery voltage to connector terminal 2 (B).

NOTICE:

Do not apply positive (+) battery voltage to any terminals other than terminal 2 (B) to avoid damaging the pulse sensor inside the motor.

(b) Connect a ground lead to connector terminals 1 (GND) and 7 (DOWN) or 10 (UP).

OK:

Measurement Condition	Specified Condition
Connect a positive (+) battery lead to terminal 2 (B), connect a negative (-) battery lead to terminal 1 (GND), and keep them connected for 3 seconds or more. With terminals 2 (B) and 1 (GND) connected, connect a negative (-) battery lead to terminal 10 (UP). Disconnect and reconnect a negative (-) battery lead to terminal 10 (UP) within 1 second.	Motor gear rotates counterclockwise (Up)
Connect a positive (+) battery lead to terminal 2 (B), connect a negative (-) battery lead to terminal 1 (GND), and keep them connected for 3 seconds or more. With terminals 2 (B) and 1 (GND) connected, connect a negative (-) battery lead to terminal 7 (DOWN). Disconnect and reconnect a negative (-) battery lead to terminal 7 (DOWN) within 1 second.	Motor gear rotates clockwise (Down)

Text in Illustration

*1	Component without harness connected (to Rear Power Window Regulator Motor Assembly RH)

If the result is not as specified, replace the rear power window regulator motor assembly RH.

CAUTION:

Reset the power window regulator motor (initialize the pulse sensor) after installing the power window regulator motor and regulator assembly onto the door.

Components

COMPONENTS ILLUSTRATION ILLUSTRATION ...

Removal

REMOVAL CAUTION / NOTICE / HINT HINT: Use the same procedure for the RH side and LH side. The procedure listed below is for the LH side. PROCEDURE 1. DISCONNECT CABLE FROM NEGAT ...

Other materials about Toyota Venza:

Cold Start Ignition Timing Performance (P050B)
DESCRIPTION This monitor will run when the engine is started at an engine coolant temperature of -10 to 50°C (14 to 122°F). The DTC is stored after the engine idles for 13 seconds (2 trip detection logic). The DTC is designed to monitor the ignition ti ...

Removal
REMOVAL PROCEDURE 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL NOTICE: When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page ). 2. REMOVE RADIATOR ASSEMBLY HINT: See page 3. REMOVE V-RIBBE ...

Inspection
INSPECTION PROCEDURE 1. INSPECT REAR DOOR LOCK ASSEMBLY LH (a) Check the operation of the door lock motor. (1) Apply battery voltage and check the operation of the door lock motor. OK: Measurement Condition ...