Toyota Venza: Inspection
INSPECTION
PROCEDURE
1. INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/o Memory)
(a) The L position of the left/right adjustment switch: Measure the resistance according to the value(s) in the table below.
Standard Resistance (for Left Side):
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
4 (MLV) - 8 (B) 6 (M+) - 7 (E) |
UP |
Below 1 Ω |
|
OFF |
10 kΩ or higher |
|
|
4 (MLV) - 7 (E) 6 (M+) - 8 (B) |
DOWN |
Below 1 Ω |
|
OFF |
10 kΩ or higher |
|
|
5 (MLH) - 8 (B) 6 (M+) - 7 (E) |
LEFT |
Below 1 Ω |
|
OFF |
10 kΩ or higher |
|
|
5 (MLH) - 7 (E) 6 (M+) - 8 (B) |
RIGHT |
Below 1 Ω |
|
OFF |
10 kΩ or higher |
|
*a |
Component without harness connected (Outer Mirror Switch Assembly) |
If the result is not as specified, replace the switch assembly.
(b) The R position of the left/right adjustment switch: Measure the resistance according to the value(s) in the table below.
Standard Resistance (for Right Side):
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
3 (MRV) - 8 (B) 6 (M+) - 7 (E) |
UP |
Below 1 Ω |
|
OFF |
10 kΩ or higher |
|
|
3 (MRV) - 7 (E) 6 (M+) - 8 (B) |
DOWN |
Below 1 Ω |
|
OFF |
10 kΩ or higher |
|
|
2 (MRH) - 8 (B) 6 (M+) - 7 (E) |
LEFT |
Below 1 Ω |
|
OFF |
10 kΩ or higher |
|
|
2 (MRH) - 7 (E) 6 (M+) - 8 (B) |
RIGHT |
Below 1 Ω |
|
OFF |
10 kΩ or higher |
|
*a |
Component without harness connected (Outer Mirror Switch Assembly) |
If the result is not as specified, replace the switch assembly.
2. INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/ Memory)
|
(a) Check the switch functions. (1) Measure the resistance according to the value(s) in the table below. Standard Resistance:
If the result is not as specified, replace the outer mirror switch assembly. |
|
(b) Check the mirror retract switch.
|
(1) Measure the resistance according to the value(s) in the table below. Standard Resistance:
If the result is not as specified, replace the outer mirror switch assembly. |
|
Removal
REMOVAL
PROCEDURE
1. REMOVE FRONT DOOR SCUFF PLATE LH
2. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH
3. REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL
4. REMOVE OUTER MIRROR SWITCH ASSEMBLY
...
Installation
INSTALLATION
PROCEDURE
1. INSTALL OUTER MIRROR SWITCH
(a) Engage the 4 claws to install the outer mirror switch.
2. INSTALL OUTER MIRROR S ...
Other materials about Toyota Venza:
Inside Vehicle
General Maintenance
GENERAL MAINTENANCE
CAUTION / NOTICE / HINT
These are maintenance and inspection items that are considered to be
the owner's responsibility.
The owner can do them or they can have them done at a service center.
The ...
On-vehicle Inspection
ON-VEHICLE INSPECTION
PROCEDURE
1. INSPECT SPEEDOMETER
(a) Check the operation.
(1) Using a speedometer tester (calibrated chassis dynamometer), check the speedometer
indication according to the table below.
Reference:
Chassis Dynamometer In ...
Inspection
INSPECTION
PROCEDURE
1. INSPECT INNER REAR VIEW MIRROR ASSEMBLY
(a) Inspect operation of the electrochromic inner mirror.
(1) Connect a positive (+) lead from the battery to terminal 1 and a negative
(-) lead to terminal 2.
(2) Press the AUTO switch.
...
0.1298