Toyota Venza: Inspection

Toyota Venza Service Manual / 1ar-fe Battery / Charging / Generator / Inspection

INSPECTION

PROCEDURE

1. INSPECT GENERATOR PULLEY WITH CLUTCH

(a) Hold the center of the pulley, and confirm that the outer ring turns counterclockwise and does not turn clockwise.

Text in Illustration

*1	Free
*2	Lock

If the result is not as specified, replace the generator pulley with clutch.

2. INSPECT GENERATOR DRIVE END FRAME BEARING

(a) Check that the bearing is not rough or worn and that it rotates smoothly.

OK:

The bearing rotates smoothly.

If the bearing does not rotate smoothly, replace the bearing.

3. INSPECT GENERATOR BRUSH HOLDER ASSEMBLY

(a) Using a vernier caliper, measure the brush length.

Text in Illustration

Length

Standard length:

9.5 to 11.5 mm (0.374 to 0.453 in.)

Minimum length:

4.5 mm (0.177 in.)

If the brush length is less than the minimum, replace the generator brush holder assembly.

4. INSPECT GENERATOR ROTOR ASSEMBLY

(a) Check that the generator rotor bearing is not rough or worn.

If the result is not as specified, replace the generator rotor assembly.

(b) Check the rotor for an open circuit.

Text in Illustration

*1	Slip Ring
*2	Ohmmeter

(1) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection	Condition	Specified Condition
130 A	Approx. 20°C (68°F)	2.3 to 2.7 Ω
150 A	Approx. 20°C (68°F)	1.5 to 1.9 Ω

If the result is not as specified, replace the generator rotor assembly.

Text in Illustration

*1	Slip Ring
*2	Ohmmeter
*3	Rotor

(1) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection	Condition	Specified Condition
Slip ring - Rotor	Always	10 kΩ or higher

If the result is not as specified, replace the generator rotor assembly.

(d) Check the slip ring diameter.

(1) Using a vernier caliper, measure the diameter of each slip ring.

Text in Illustration

Diameter

Standard diameter:

14.2 to 14.4 mm (0.559 to 0.567 in.)

Minimum diameter:

14 mm (0.551 in.)

If the diameter is less than the minimum, replace the generator rotor assembly.

Disassembly

DISASSEMBLY PROCEDURE 1. REMOVE GENERATOR PULLEY CAP (a) Using a screwdriver, puncture the center of the generator pulley cap and pry it off. NOTICE: Do not reuse the generator ...

Reassembly

REASSEMBLY PROCEDURE 1. INSTALL GENERATOR ROTOR ASSEMBLY (a) Place the generator drive end frame on the generator pulley. (b) Install the ...

Other materials about Toyota Venza:

GCWR, TWR and Unbraked TWR
Confirm that the gross trailer weight, gross combination weight, gross vehicle weight, gross axle weight and tongue weight are all within the limits. - GCWR* and TWR* ► Vehicles without towing package ► Vehicles with towing package ...

Removal
REMOVAL PROCEDURE 1. REMOVE REAR DOOR SCUFF PLATE 2. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP 3. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover) 4. REMOVE DECK BOARD ASSEMBLY 5. REMOVE NO. 3 DECK BOARD SUB-ASSEMBLY 6. REMOVE DECK S ...

Engine Hood Courtesy Switch
Components COMPONENTS ILLUSTRATION Inspection INSPECTION PROCEDURE 1. INSPECT SECURITY COURTESY SWITCH (HOOD LOCK ASSEMBLY) (a) Measure the resistance according to the value(s) in the table below. Standard Resistance: ...