INITIALIZATION
1. PROCEDURES NECESSARY WHEN BATTERY TERMINAL IS DISCONNECTED/RECONNECTED
Necessary Procedure |
Effect / Inoperative Function When Necessary Procedures are not Performed |
See Page |
---|---|---|
Reset back door close position |
|
|
NOTICE:
After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 60 seconds before disconnecting the cable from the negative (-) battery terminal.
After the ignition switch is turned off, the navigation receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 60 seconds before disconnecting the cable from the negative (-) battery terminal.
2. PROCEDURES NECESSARY WHEN ECU OR OTHER PARTS ARE REPLACED
Replacement Part |
Necessary Procedure |
Effect / Inoperative Function when Necessary Procedures are not Performed |
Note |
|
---|---|---|---|---|
ECM |
Vehicle Identification Number (VIN) registration |
MIL comes on |
for 1AR-FE for 2GR-FE |
|
ECU communication ID registration (Engine immobiliser system) |
Engine start |
*1 *2 |
||
|
Inspection after repair |
|
for 1AR-FE |
|
|
Inspection after repair |
|
for 2GR-FE |
|
Automatic transaxle assembly |
|
|
for U660F Initialization for U660F Registration for U760F Initialization for U760F Registration for U660E Initialization for U660E Registration for U760E Initialization for U760E Registration |
|
|
|
|
||
Shift solenoid valve SL1 and/or SL2 |
Perform road test to allow TCM to learn |
|
||
TCM (If possible, read the transaxle compensation code from the previous TCM) |
Possible |
|
|
|
Impossible |
|
|
||
|
Code registration (Tire pressure warning system) |
|
for registration |
|
Brake actuator assembly (Skid control ECU) |
Engine variant learning |
VSC function |
|
|
Power steering ECU |
Rotation angle sensor initialization and torque sensor zero point calibration |
|
|
|
Steering column |
Rotation angle sensor initialization and torque sensor zero point calibration |
Steering effort is different between turning steering wheel to left and right |
||
Roof console box assembly |
Re-registration of codes in the garage door opener system
|
Garage door opener system |
|
|
|
Code registration (Engine immobiliser system (w/ smart key system)) |
|
|
|
Transponder key ECU*2 |
|
Engine start |
|
|
|
Registration of recognition code (Wireless door lock control system (w/o smart key system)) |
Wireless door lock control system |
|
|
|
|
|
|
|
|
Initialize power window control system |
|
|
|
|
Initializing sliding roof ECU (pulse sensor initial position setting) |
|
|
|
|
Perform headlight leveling ECU initialization |
Headlight leveling function |
|
Precaution
PRECAUTION
NOTICE:
When disconnecting the cable from the negative (-) battery terminal, initialize
the following systems after the cable is reconnected.
System Name
See Procedure
Back Door Closer System
...
Registration
REGISTRATION
CAUTION / NOTICE / HINT
NOTICE:
When the automatic transaxle is replaced, the transaxle compensation
code must be input into the TCM (proceed to Procedure 1). After the automatic
transaxle is reinstalled, the Quick Response (QR) ...
Dtc Check / Clear
DTC CHECK / CLEAR
1. CHECK DTC
(a) Turn the ignition switch off.
(b) Connect the Techstream to the DLC3.
(c) Turn the ignition switch to ON.
(d) Turn the Techstream on.
(e) Read the DTCs following the display on the Techstream. Enter the following
menu ...