Toyota Venza: Initialization

Toyota Venza Service Manual / Lighting (ext) / Lighting System / Initialization

INITIALIZATION

NOTICE:

Initialize the headlight leveling ECU assembly (set the zero point of the height control sensor in the headlight leveling ECU assembly) after the vehicle height changes due to replacement of the suspension or after performing such operations as removal and reinstallation or replacement of the rear height control sensor sub-assembly RH.
When the headlight leveling ECU assembly is replaced, initialization is also necessary.
Adjust the headlight aim after initializing the headlight leveling ECU assembly (See page ).

When a malfunction is detected in the automatic headlight beam level control system, height control sensor signal initialization is impossible. Perform troubleshooting before initialization.

1. 1.PREPARE VEHICLE FOR INITIALIZATION

(a) Unload the vehicle and its trunk, ensuring that the spare tire, tools and jack are in their original positions.

(b) Check that there are no passengers in the vehicle.

(d) Stop the vehicle on a level surface and keep the vehicle height unchanged.

Proceed to
NEXT

2. 2.CHECK HEADLIGHT BEAM LEVEL CONTROL INDICATOR LIGHT

(a) Turn the ignition switch to ON, and check the indicator light.

OK:

Condition	Specified Condition
The headlight leveling ECU assembly is replaced with a new one.	Indicator light continuously blinks 6 times at 2 Hz.
Removal and reinstallation of the headlight leveling ECU assembly, replacement of the rear height control sensor sub-assembly RH, removal and reinstallation of the rear height control sensor sub-assembly RH, replacement of the suspension, etc. is performed.	Indicator light comes on for approximately 3 seconds, and then goes off (bulb check function).

HINT:

If the indicator light does not come on when turning the ignition switch to ON, inspect and repair it according to Problem Symptoms Table (See page ).

Result	Proceed to
NG	GO TO PROBLEM SYMPTOMS TABLE
OK	GO TO STEP 3

3. 3.INITIALIZATION

(a) Connect terminals 4 (CG) and 8 (LVL) of the DLC3 using SST.

SST: 09843-18040

(b) Turn the low beam headlights on and off using the light control switch within 20 seconds after connecting the terminals.

HINT:

The number of times the low beam headlights need to be turned on and off is determined by the present fuel level as shown below.

Fuel Level	Number of Times to Turn Low Beam Headlights on and off
Fuel level is within A range.	1
Fuel level is within B range.	2
Fuel level is within C range.	3
Fuel level is within D range.	4
Fuel level is within E range.	5

NOTICE:

Turn the low beam headlights on and off at approximately 1-second intervals.
Be sure to operate the light control switch from outside the vehicle.

OK:

Condition	Specified Condition
The headlight leveling ECU assembly is replaced with a new one.	Blinks 6 times at 2 Hz → Continuously blinks N*1 times at 2 Hz.
Removal and reinstallation of the headlight leveling ECU assembly, replacement of the rear height control sensor sub-assembly RH, removal and reinstallation of the rear height control sensor sub-assembly RH, replacement of the suspension, etc. is performed.	Off → Continuously blinks N*1 times at 2 Hz.

HINT:

*1: The number of times that the indicator blinks is determined by the number of times the low beam headlights are turned on and off.
If initialization cannot be finished normally, disconnect SST from the DLC3 and turn the ignition switch off. Then, restart from procedure 1.

Result	Proceed to
NG	GO TO PROBLEM SYMPTOMS TABLE
OK	TURN IGNITION SWITCH OFF (END)

Customize Parameters

CUSTOMIZE PARAMETERS 1. CUSTOMIZE LIGHTING SYSTEM (EXT) HINT: The following items can be customized. NOTICE: When the customer requests a change in a function, first make sure that th ...

Problem Symptoms Table

PROBLEM SYMPTOMS TABLE Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of pro ...

Other materials about Toyota Venza:

Wireless Transmitter Memory Function does not Operate
DESCRIPTION With the ignition switch off and the driver door closed, pressing the manual lock or unlock switch on the power window regulator master switch assembly while holding a seat memory switch (M1 switch or M2 switch) will register the transmitter ...

Reassembly
REASSEMBLY PROCEDURE 1. INSTALL BEARING BRACKET HOLE SNAP RING (for RH Side) (a) Install a new bearing bracket hole snap ring to the front drive shaft assembly RH. 2. INSTALL FRONT DRIVE SHAFT BEARING (for RH Side) (a) Using SST, install a ne ...

TS and CG Terminal Circuit
DESCRIPTION In the Test Mode (signal check), a malfunction in the speed sensor that cannot be detected when the vehicle is stopped can be detected while driving. Transition to the sensor check mode can be performed by connecting terminals TS and CG of th ...