Toyota Venza manuals

Toyota Venza: Headlight Relay Circuit

DESCRIPTION

The main body ECU (driver side junction block assembly) controls the headlight relays.

WIRING DIAGRAM



CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

PROCEDURE

1.

PERFORM ACTIVE TEST USING TECHSTREAM

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / Main Body / Active Test.

(e) Check that the relays operate.

Main Body

Tester Display

Test Part

Control Range

Diagnostic Note

Headlight Relay

Headlight Relay

ON/OFF

-

OK:

Headlight relays operate. (Low beam headlights illuminate.)


OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE


NG

2.

INSPECT ENGINE ROOM JUNCTION BLOCK ASSEMBLY

(a) Remove the power distributor (engine room junction block assembly) from the engine room relay block (See page ).



(b) Connect a positive (+) lead from the battery to terminal 1A-1.

(c) Connect a negative (-) lead from the battery to terminal 1F-17.

(d) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

1D-1 - Battery negative

Always

11 to 14 V

1D-2 - Battery negative

Always

11 to 14 V

Text in Illustration

*1

Component without harness connected

(Power Distributor (Engine Room Junction Block Assembly))


NG

REPLACE POWER DISTRIBUTOR (ENGINE ROOM JUNCTION BLOCK ASSEMBLY)


OK

3.

CHECK HARNESS AND CONNECTOR (BATTERY - ENGINE ROOM JUNCTION BLOCK ASSEMBLY)

(a) Disconnect the 1A power distributor (engine room junction block assembly) connector.


(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connector

Condition

Specified Condition

1A-1 - Body ground

Always

11 to 14 V

Text in Illustration

*1

Front view of wire harness connector

(to Power Distributor (Engine Room Junction Block Assembly))


NG

REPAIR OR REPLACE HARNESS OR CONNECTOR


OK

4.

CHECK HARNESS AND CONNECTOR (ENGINE ROOM JUNCTION BLOCK ASSEMBLY - MAIN BODY ECU)

(a) Disconnect the 1F power distributor (engine room junction block assembly) connector.


(b) Disconnect the 2G main body ECU (driver side junction block assembly) connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

1F-17 - 2G-35

Always

Below 1 Ω

1F-17 - Body ground

Always

10 kΩ or higher

Text in Illustration

*1

Front view of wire harness connector

(to Power Distributor (Engine Room Junction Block Assembly))

*2

Front view of wire harness connector

(to Main Body ECU (Driver Side Junction Block Assembly))


OK

REPLACE MAIN BODY ECU (DRIVER SIDE JUNCTION BLOCK ASSEMBLY)


NG

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

Steering Position Sensor Malfunction (B2414)
DESCRIPTION The AFS ECU (headlight swivel ECU assembly) receives signals indicating the swerve-angle from the steering angle sensor using CAN communication. DTC No. DTC Detec ...

Headlight Solenoid Circuit
DESCRIPTION for HID Headlight: When the main body ECU receives a high beam turn on signal, the main body ECU activates the bi-function by controlling the BI-XENON relay. The bi-func ...

Other materials about Toyota Venza:

Inspection
INSPECTION PROCEDURE 1. INSPECT FRONT SEAT FRAME WITH ADJUSTER LH (a) Check operation of the seat frame (slide motor). (1) w/ Memory: Check if the seat frame moves smoothly when the battery is connected to the slide motor connector termin ...

Problem Symptoms Table
PROBLEM SYMPTOMS TABLE HINT: Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of probability in the "Suspected Area" ...

Driver Side Power Window does not Operate with Power Window Master Switch
DESCRIPTION When the engine is running or the ignition switch is ON, the power window regulator motor assembly (for driver side) is operated by the power window regulator master switch assembly. The power window regulator motor assembly (for driver side) ...

© 2016-2024 Copyright www.tovenza.com

0.1327