Toyota Venza manuals

Toyota Venza: Front Stabilizer Bar(for 2gr-fe 2wd)

Toyota Venza Service Manual / Front Suspension / Front Stabilizer Bar(for 2gr-fe 2wd)

Components

COMPONENTS

ILLUSTRATION


Removal

REMOVAL

PROCEDURE

1. REMOVE FRONT FRAME ASSEMBLY (When Using the Engine Support Bridge)

(See page )


2. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE (When Not Using the Engine Support Bridge)

(See page )


3. SEPARATE FRONT STABILIZER LINK ASSEMBLY LH

(a) Remove the nut and separate the front stabilizer link assembly LH.

HINT:

If the ball joint turns together with the nut, use a hexagon wrench (6 mm) to hold the stud bolt.


4. SEPARATE FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.

5. REMOVE FRONT NO. 1 STABILIZER BRACKET LH

(a) Remove the 2 bolts and front No. 1 stabilizer bracket LH from the front frame assembly.


6. REMOVE FRONT NO. 1 STABILIZER BRACKET RH

HINT:

Perform the same procedure as for the LH side.

7. REMOVE FRONT STABILIZER BAR

(a) Remove the front stabilizer bar from the front frame assembly.

8. REMOVE FRONT NO. 2 STABILIZER BRACKET LH

(a) Remove the front No. 2 stabilizer bracket LH from the front No. 1 stabilizer bar bushing.


9. REMOVE FRONT NO. 2 STABILIZER BRACKET RH

HINT:

Perform the same procedure as for the LH side.

10. REMOVE FRONT NO. 1 STABILIZER BAR BUSHING

(a) Remove the 2 front No. 1 stabilizer bar bushings from the front stabilizer bar.

Inspection

INSPECTION

PROCEDURE

1. INSPECT FRONT STABILIZER LINK ASSEMBLY

(a) Inspect the turning torque of the ball joint.

(1) Secure the front stabilizer link assembly in a vise using aluminum plates.

(2) Install the nut to the front stabilizer link assembly stud.

(3) Using a torque wrench, turn the nut continuously at a rate of 3 to 5 seconds per turn and take the torque reading on the 5th turn.

Turning torque:

0.05 to 1.96 N*m (0.5 to 20 kgf*cm, 0.4 to 17 in.*lbf)

If the turning torque is not within the specified range, replace the front stabilizer link assembly with a new one.


(b) Inspect the dust cover.

(1) Check that the dust cover is not cracked and that there is no grease on it.

Installation

INSTALLATION

PROCEDURE

1. INSTALL FRONT NO. 1 STABILIZER BAR BUSHING

(a) Install the 2 front No. 1 stabilizer bar bushings to the front stabilizer bar as shown in the illustration.

Text in Illustration

*1

Cutout

*2

Front of the Vehicle

*3

Inside of the Vehicle

NOTICE:

When installing the front No. 1 stabilizer bar bushings, make sure that the cutout faces the rear of the vehicle.


2. INSTALL FRONT NO. 2 STABILIZER BRACKET LH

(a) Install the front No. 2 stabilizer bracket LH to the front No. 1 stabilizer bar bushing.


3. INSTALL FRONT NO. 2 STABILIZER BRACKET RH

HINT:

Perform the same procedure as for the LH side.

4. INSTALL FRONT STABILIZER BAR

(a) Install the front stabilizer bar to the front frame assembly.

5. INSTALL FRONT NO. 1 STABILIZER BRACKET LH

(a) Install the front No. 1 stabilizer bracket LH to the front frame assembly with the 2 bolts.

Torque:

29 N·m {296 kgf·cm, 21 ft·lbf}


6. INSTALL FRONT NO. 1 STABILIZER BRACKET RH

HINT:

Perform the same procedure as for the LH side.

7. INSTALL FRONT STABILIZER LINK ASSEMBLY LH

(a) Install the front stabilizer link assembly LH with the nut.

Torque:

74 N·m {755 kgf·cm, 55 ft·lbf}

HINT:

If the ball joint turns together with the nut, use a hexagon wrench (6 mm) to hold the stud bolt.


8. INSTALL FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.

9. INSTALL FRONT FRAME ASSEMBLY (When Using the Engine Support Bridge)

(See page )


10. INSTALL ENGINE ASSEMBLY WITH TRANSAXLE (When Not Using the Engine Support Bridge)

(See page )


Front Stabilizer Bar(for 1ar-fe 2wd)
Components COMPONENTS ILLUSTRATION Inspection INSPECTION PROCEDURE 1. INSPECT FRONT STABILIZER LINK ASSEMBLY (a) Inspect the turning torque of the ball joint. (1) Secure the ...

Front Suspension Member(when Not Using The Engine Support Bridge)
...

Other materials about Toyota Venza:

Headlight Leveling Ecu
Components COMPONENTS ILLUSTRATION Removal REMOVAL PROCEDURE 1. REMOVE HEADLIGHT LEVELING ECU ASSEMBLY (a) Disconnect the connector. (b) Remove the bolt and headlight leveling ECU assembly ...

Problem Symptoms Table
PROBLEM SYMPTOMS TABLE HINT: Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of probability in the "Suspected Area" ...

Disposal
DISPOSAL CAUTION / NOTICE / HINT CAUTION: Before performing pre-disposal deployment of any SRS component, review and closely follow all applicable environmental and hazardous material regulations. Pre-disposal deployment may be considered hazardous mate ...

© 2016-2024 Copyright www.tovenza.com

0.1472