Toyota Venza: Front Passenger Side Power Window Switch

Toyota Venza Service Manual / Window / Glass / Front Passenger Side Power Window Switch

Components

COMPONENTS

ILLUSTRATION

Removal

REMOVAL

PROCEDURE

1. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL

(a) Using a moulding remover, disengage the 2 clips and 4 claws.

(b) Disconnect the connector and remove the power window regulator switch assembly with front door armrest base panel.

2. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY

(a) Disengage the 2 claws and remove the power window regulator switch assembly.

Inspection

INSPECTION

PROCEDURE

1. INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY

(a) Check the switch function.

(1) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection	Switch Condition	Specified Condition
6 (UP) - 1 (GND)	Auto up or up position	Below 1 Ω
7 (DOWN) - 1 (GND)	Auto down or down position	Below 1 Ω
8 (AUTO) - 1 (GND)	Auto up or auto down position	Below 1 Ω
6 (UP) - 1 (GND)	Free	10 kΩ or higher
7 (DOWN) - 1 (GND)	Free	10 kΩ or higher
8 (AUTO) - 1 (GND)	Free	10 kΩ or higher

Text in Illustration

*1	Component without harness connected (to Power Window Regulator Switch Assembly (for Front Passenger Side))

If the result is not as specified, replace the power window regulator switch assembly (for front passenger side).

(b) Check that the LED illuminates.

(1) Apply battery voltage to the power window regulator switch assembly and check that the LED illuminates.

OK:

Measurement Condition

Specified Condition

Battery positive (+) → 4 (LED)

Battery negative (-) → 1 (GND)

LED illuminates

Text in Illustration

*1	Component without harness connected (to Power Window Regulator Switch Assembly (for Front Passenger Side))

If the result is not as specified, replace the power window regulator switch assembly (for front passenger side).

Installation

INSTALLATION

PROCEDURE

1. INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY

(a) Engage the 2 claws to install the power window regulator switch assembly.

2. INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL

(a) Connect the connector.

(b) Engage the 2 clips and 4 claws, and install the power window regulator switch assembly with front door armrest base panel.

Removal

REMOVAL PROCEDURE 1. REMOVE UPPER BACK WINDOW PANEL TRIM 2. REMOVE BACK DOOR PANEL TRIM ASSEMBLY 3. DISCONNECT POWER BACK DOOR ROD (w/ Power Back Door) 4. REMOVE BACK DOOR TRIM COVER LH ...

Other materials about Toyota Venza:

Installation
INSTALLATION CAUTION / NOTICE / HINT HINT: Perform "Inspection After Repair" after replacing the camshaft, No. 2 camshaft, camshaft timing gear assembly, camshaft timing exhaust gear assembly or cylinder head sub-assembly (See page ). PROCED ...

USB Audio System Recognition/Play Error
DESCRIPTION When a USB device or "iPod" is connected to the USB jack of the No. 1 stereo jack adapter assembly, it must have playable files. The device must also communicate with and be recognized by the radio and display receiver assembly. This ...

Precaution
PRECAUTION 1. NOTICE FOR INITIALIZATION CAUTION: When disconnecting the cable from the negative (-) battery terminal, initialize the following system after the cable is reconnected. System Name See Procedure Back Do ...

Toyota Venza: Front Passenger Side Power Window Switch

Removal

Front Side Fix Window Glass

Other materials about Toyota Venza: