Toyota Venza manuals

Toyota Venza: Front Occupant Classification Sensor LH Collision Detection (B1785)

Toyota Venza Service Manual / Supplemental Restraint Systems / Occupant Classification System / Front Occupant Classification Sensor LH Collision Detection (B1785)

DESCRIPTION

DTC B1785 is output when the occupant classification ECU receives a collision detection signal sent by the front occupant classification sensor LH if an accident occurs.

DTC B1785 is also output when the front seat assembly RH is subjected to a strong impact, even if an actual accident does not occur.

However, when the occupant classification ECU outputs a collision detection signal, even if the vehicle is not in a collision, DTC B1785 can be cleared by Zero Point Calibration and Sensitivity Check.

Therefore, if DTC B1785 is output, first perform Zero Point Calibration and Sensitivity Check.

DTC No.

DTC Detection Condition

Trouble Area

B1785

  • Front seat assembly RH malfunction
  • Occupant classification ECU malfunction
  • Front occupant classification sensor LH sensed large load
  • Front seat frame with adjuster assembly RH (Front occupant classification sensor LH)
  • Occupant classification ECU

HINT:

When DTC B1650/32 is detected as a result of troubleshooting for the airbag system, check the DTCs stored in the occupant classification ECU. When DTC B1785 is output, perform troubleshooting for the DTC.

WIRING DIAGRAM


PROCEDURE

1.

PERFORM ZERO POINT CALIBRATION

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Using the Techstream, perform Zero Point Calibration (See page ).


OK:

"Zero Point Calibration is complete." is displayed.


NG

GO TO STEP 4


OK

2.

PERFORM SENSITIVITY CHECK

(a) Using the Techstream, perform Sensitivity Check (See page ).


Standard:

27 to 33 kg (59.5 to 72.8 lb)


NG

GO TO STEP 4


OK

3.

CHECK DTC

(a) Turn the ignition switch to ON.

(b) Clear the DTCs stored in the occupant classification ECU (See page ).


(c) Clear the DTCs stored in the center airbag sensor assembly (See page ).


(d) Turn the ignition switch off.

(e) Turn the ignition switch to ON.

(f) Check for DTCs (See page ).


OK:

DTC B1785 is not output.

HINT:

Codes other than DTC B1785 may be output at this time, but they are not related to this check.


OK

END


NG

4.

REPLACE FRONT SEAT FRAME WITH ADJUSTER ASSEMBLY RH

(a) Turn the ignition switch off.

(b) Disconnect the cable from the negative (-) battery terminal.

(c) Replace the front seat frame with adjuster assembly RH (See page for power seat or
for manual seat).


HINT:

Perform the inspection using parts from a normal vehicle if possible.


NEXT

5.

PERFORM ZERO POINT CALIBRATION

(a) Connect the cable to the negative (-) battery terminal.

(b) Connect the Techstream to the DLC3.

(c) Turn the ignition switch to ON.

(d) Using the Techstream, perform Zero Point Calibration (See page ).


OK:

"Zero Point Calibration is complete." is displayed.


NG

GO TO STEP 8


OK

6.

PERFORM SENSITIVITY CHECK

(a) Using the Techstream, perform Sensitivity Check (See page ).


Standard:

27 to 33 kg (59.5 to 72.8 lb)


NG

GO TO STEP 8


OK

7.

CHECK DTC

(a) Turn the ignition switch to ON.

(b) Clear the DTCs stored in the occupant classification ECU (See page ).


(c) Clear the DTCs stored in the center airbag sensor assembly (See page ).


(d) Turn the ignition switch off.

(e) Turn the ignition switch to ON.

(f) Check for DTCs (See page ).


OK:

DTC B1785 is not output.

HINT:

Codes other than DTC B1785 may be output at this time, but they are not related to this check.


OK

END


NG

8.

REPLACE OCCUPANT CLASSIFICATION ECU

(a) Turn the ignition switch off.

(b) Disconnect the cable from the negative (-) battery terminal.

(c) Replace the occupant classification ECU (See page ).



NEXT

9.

PERFORM ZERO POINT CALIBRATION

(a) Connect the cable to the negative (-) battery terminal.

(b) Connect the Techstream to the DLC3.

(c) Turn the ignition switch to ON.

(d) Using the Techstream, perform Zero Point Calibration (See page ).


OK:

"Zero Point Calibration is complete." is displayed.


NEXT

10.

PERFORM SENSITIVITY CHECK

(a) Using the Techstream, perform Sensitivity Check (See page ).


Standard:

27 to 33 kg (59.5 to 72.8 lb)


NEXT

END

Front Occupant Classification Sensor RH Collision Detection (B1786)
DESCRIPTION DTC B1786 is output when the occupant classification ECU receives a collision detection signal sent by the front occupant classification sensor RH if an accident occurs. DTC B1786 is ...

Rear Occupant Classification Sensor LH Circuit Malfunction (B1782)
DESCRIPTION The rear occupant classification sensor LH circuit consists of the occupant classification ECU and rear occupant classification sensor LH. DTC B1782 is recorded when a malfunction is d ...

Other materials about Toyota Venza:

Problem Symptoms Table
PROBLEM SYMPTOMS TABLE HINT: Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of probability in the "Suspected Area" column of ...

Parking Brake System
Problem Symptoms Table PROBLEM SYMPTOMS TABLE HINT: Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of probability in the "Suspe ...

Dtc Check / Clear
DTC CHECK / CLEAR NOTICE: When the diagnosis system is changed from normal mode to check mode or vice versa, all DTCs and freeze frame data recorded in normal mode are cleared. Before changing modes, always check and make a note of DTCs and freeze frame ...

© 2016-2024 Copyright www.tovenza.com

0.1225