Toyota Venza: Front Crankshaft Oil Seal

Toyota Venza Service Manual / 1ar-fe Engine Mechanical / Front Crankshaft Oil Seal

Components

COMPONENTS

ILLUSTRATION

Removal

REMOVAL

PROCEDURE

1. REMOVE FRONT WHEEL RH

2. REMOVE NO. 1 ENGINE UNDER COVER

3. SEPARATE FRONT FENDER LINER RH

4. REMOVE FRONT FENDER APRON SEAL RH

5. REMOVE V-RIBBED BELT

6. REMOVE CRANKSHAFT PULLEY

(a) Using SST, hold the crankshaft pulley and loosen the pulley bolt. Further loosen the bolt until 2 or 3 threads are screwed into the crankshaft.

SST: 09213-54015

SST: 09330-00021

HINT:

Part number of installation bolt for SST (crankshaft pulley holding tool): 91551-80650 (quantity: 2)

(b) Using SST and the pulley bolt, remove the crankshaft pulley.

SST: 09950-50013

09951-05010

09952-05010

09953-05020

09954-05011

HINT:

Apply a lubricant to the threads and end of SST.

7. REMOVE TIMING CHAIN COVER OIL SEAL

(a) Using a screwdriver, pry out the oil seal.

HINT:

Tape the screwdriver tip before use.

NOTICE:

Do not damage the surface of the oil seal press fit hole or the crankshaft.

Installation

INSTALLATION

PROCEDURE

1. INSTALL TIMING CHAIN COVER OIL SEAL

(a) Apply MP grease to the lip of a new oil seal.

NOTICE:

Do not allow foreign matter to contact the lip of the oil seal.
Do not allow MP grease to contact the dust seal.

(b) Using SST and a hammer, tap in the oil seal until its surface is flush with the timing chain cover edge.

SST: 09223-22010

NOTICE:

Keep the lip of the oil seal free from foreign matter.
Do not tap in the oil seal at an angle.

2. INSTALL CRANKSHAFT PULLEY

(a) Align the pulley set key with the key groove of the crankshaft pulley.

(b) Using SST, hold the crankshaft pulley and install the pulley bolt.

SST: 09213-54015

SST: 09330-00021

Torque:

260 N·m {2651 kgf·cm, 192 ft·lbf}

HINT:

Part number of installation bolt for SST (crankshaft pulley holding tool): 91551-80650 (quantity: 2)

3. INSTALL V-RIBBED BELT

4. INSTALL FRONT FENDER APRON SEAL RH

5. INSTALL FRONT FENDER LINER RH

6. INSTALL NO. 1 ENGINE UNDER COVER

7. INSTALL FRONT WHEEL RH

Torque:

103 N·m {1050 kgf·cm, 76 ft·lbf}

Reassembly

REASSEMBLY PROCEDURE 1. INSTALL STIFFENING CRANKCASE RING PIN NOTICE: It is not necessary to remove the ring pin unless it is being replaced. (a) Using a plastic-faced hammer, tap in 2 ...

Other materials about Toyota Venza:

Compressor Lock Sensor Circuit (B1422/22)
SYSTEM DESCRIPTION The ECM sends the engine speed signal to the A/C amplifier via CAN communication. The A/C amplifier reads the difference between compressor speed and engine speed. When the difference becomes too large, the A/C amplifier determines that ...

Precaution
PRECAUTION 1. NOTICE FOR INITIALIZATION CAUTION: When disconnecting the cable from the negative (-) battery terminal, initialize the following system after the cable is reconnected. System Name See Procedure Back Do ...

Sound Signal Circuit between Navigation Receiver Assembly and Stereo Component Amplifier
DESCRIPTION The navigation receiver assembly sends a sound signal to the stereo component amplifier assembly via this circuit. The sound signal that has been sent is amplified by the stereo component amplifier assembly, and then is sent to the speakers. ...

Toyota Venza: Front Crankshaft Oil Seal

Reassembly

Rear Crankshaft Oil Seal

Other materials about Toyota Venza: