Toyota Venza: Front Axle Hub Bolt
Components
COMPONENTS
ILLUSTRATION
Replacement
REPLACEMENT
CAUTION / NOTICE / HINT
HINT:
- Use the same procedure for the RH side and LH side.
- The procedure listed below is for the LH side.
PROCEDURE
1. REMOVE FRONT WHEEL
2. SEPARATE FRONT DISC BRAKE CALIPER ASSEMBLY
|
(a) Remove the 2 bolts and separate the front disc brake caliper assembly. NOTICE: Use wire or an equivalent tool to keep the front disc brake caliper assembly from hanging down by the flexible hose. |
|
3. REMOVE FRONT DISC
.gif)
4. REMOVE FRONT AXLE HUB BOLT
|
(a) Position the front axle hub bolt to be removed as shown in the illustration. |
|
|
(b) Temporarily install the 2 nuts to the front axle hub bolt as shown in the illustration. Recommended service nut: Thread diameter: 12.0 mm (0.472 in.) Thread pitch: 1.5 mm (0.0591 in.) NOTICE: Install the nuts to prevent damage to the front axle hub bolts. |
|
(c) Using SST and a brass bar or an equivalent tool to hold the front axle hub, remove the front axle hub bolt.
SST: 09628-10011
Text in Illustration|
*1 |
Turn |
|
*2 |
Hold |
|
*3 |
Nut |
5. INSTALL FRONT AXLE HUB BOLT
|
(a) Position a new front axle hub bolt to be installed as shown in the illustration. |
|
|
(b) Temporarily install the new front axle hub bolt to the front axle hub. |
|
(c) Install a washer and nut to the new front axle hub bolt as shown in the illustration.
Recommended service nut:
Thread diameter: 12.0 mm (0.472 in.)
Thread pitch: 1.5 mm (0.0591 in.)
HINT:
The thickness of the washer is preferably 5 mm (0.197 in.) or more.
(d) Using a brass bar or an equivalent tool to hold the front axle hub, install the front axle hub bolt by tightening the nut.
Text in Illustration|
*1 |
Washer |
|
*2 |
Turn |
|
*3 |
Hold |
|
*4 |
Nut |
NOTICE:
- Install the nuts to prevent damage to the front axle hub bolts.
- Do not damage the threads of the front axle hub bolts.
(e) Remove the 3 nuts and washer from the 3 front axle hub bolts.
6. INSTALL FRONT DISC
7. INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY
|
(a) Install the front disc brake caliper assembly to the steering knuckle with the 2 bolts. Torque: 104 N·m {1060 kgf·cm, 77 ft·lbf} NOTICE: Do not twist the brake hose when installing the front disc brake caliper assembly. |
|
8. INSTALL FRONT WHEEL
Torque:
103 N·m {1050 kgf·cm, 76 ft·lbf}
Installation
INSTALLATION
CAUTION / NOTICE / HINT
HINT:
Use the same procedure for the RH side and LH side.
The procedure listed below is for the LH side.
PROCEDURE
1. INSTALL FRONT AXLE HUB ...
Other materials about Toyota Venza:
Seat Position Airbag Sensor Circuit Malfunction (B1653/35)
DESCRIPTION
The seat position airbag sensor circuit consists of the center airbag sensor
assembly and seat position airbag sensor.
DTC B1653/35 is stored when a malfunction is detected in the seat position airbag
sensor circuit.
DTC No.
...
How To Proceed With Troubleshooting
CAUTION / NOTICE / HINT
HINT:
Use the following procedure to troubleshoot.
*: Use the Techstream.
PROCEDURE
1.
VEHICLE BROUGHT TO WORKSHOP
NEXT
...
Speed Signal Malfunction (B15C2)
DESCRIPTION
The navigation receiver assembly receives a vehicle speed signal from the combination
meter assembly and information from the navigation antenna assembly, and then adjusts
the vehicle position.
The navigation receiver assembly stores this DTC ...
0.1669