Toyota Venza: ECM / PCM Processor (P0606)

Toyota Venza Service Manual / 1ar-fe Engine Control / Sfi System / ECM / PCM Processor (P0606)

MONITOR DESCRIPTION

The ECM continuously monitors its main and sub CPUs. This self-check ensures that the ECM is functioning properly. If outputs from the CPUs are different and deviate from the standard, the ECM illuminates the MIL and stores the DTC immediately.

DTC No.	DTC Detection Condition	Trouble Area
P0606	An ECM main CPU error (1 trip detection logic)	ECM

MONITOR STRATEGY

Related DTC	P0606: ECM Processor Performance
Required Sensors/Components (Main)	ECM
Required Sensors/Components (Related)	-
Frequency of Operation	Continuous
Duration	Within 1 second
MIL Operation	Immediate
Sequence of Operation	None

TYPICAL ENABLING CONDITIONS

Monitor runs whenever the following DTCs are not stored	None
All of the following conditions are met	-
Battery voltage	8 V or higher
Ignition switch	ON
Starter	OFF

TYPICAL MALFUNCTION THRESHOLDS

Either of the following conditions is met	-
DMA communication	No response
Watchdog from monitoring processor	Not toggle

CONFIRMATION DRIVING PATTERN

Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the Techstream off.
Turn the ignition switch off.
Disconnect the Techstream.
Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.
Connect the cable to the negative (-) battery terminal.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Wait 1 second or more.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the pending DTCs.
HINT:
- If a pending DTC is output, the system is malfunctioning.
- If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P0606.

Check the DTC judgment result.

Techstream Display	Description
NORMAL	DTC judgment completed System normal
ABNORMAL	DTC judgment completed System abnormal
INCOMPLETE	DTC judgment not completed Perform driving pattern after confirming DTC enabling conditions
N/A	Unable to perform DTC judgment Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

HINT:

If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.

If the judgment result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (See page ).
HINT:
- If a permanent DTC is output, the system is malfunctioning.
- If no permanent DTC is output, the system is normal.

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE

1.	READ OUTPUT DTC (DTC P0606)

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(d) Clear the DTCs (See page ).

(e) Turn the ignition switch off and turn the Techstream off.

(f) Disconnect the Techstream.

(g) Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.

(h) Connect the cable to the negative (-) battery terminal.

(i) Connect the Techstream to the DLC3.

(j) Turn the ignition switch to ON.

(k) Turn the Techstream on.

(l) Wait 1 second or more.

(m) Enter the following menus: Powertrain / Engine / Trouble Codes.

(n) Read the DTCs.

Result	Proceed to
DTC is not output	A
DTC P0606 is output	B

CHECK FOR INTERMITTENT PROBLEMS

REPLACE ECM

Random Access Memory (RAM) (P0604)

MONITOR DESCRIPTION The ECM continuously monitors its internal memory status. This self-check ensures that the ECM is functioning properly. It is diagnosed by internal "mirroring" of th ...

Control Module Performance (P0607)

MONITOR DESCRIPTION The ECM continuously monitors its internal processors (CPUs) and heated oxygen sensor transistors. This self-check ensures that the ECM is functioning properly. DTC ...

Other materials about Toyota Venza:

Door Unlock Detection Switch Circuit
DESCRIPTION The main body ECU (driver side junction block assembly) detects the condition of the door unlock detection switch. WIRING DIAGRAM PROCEDURE 1. READ VALUE USING TECHSTREAM (a) Connect the Techstream to the DL ...

CD cannot be Inserted or is Ejected Right After Insertion
PROCEDURE 1. CHECK IF A PROPER CD IS INSERTED (a) Make sure that the CD is an audio CD or a CD with an MP3, WMA or AAC files, and that it is not deformed, flawed, stained, deteriorated or otherwise defective. OK: Normal C ...

How To Proceed With Troubleshooting
CAUTION / NOTICE / HINT HINT: The wireless door lock control system troubleshooting procedures are based on the premise that the power door lock control system is operating normally. Check the power door lock control system first before troub ...