Toyota Venza manuals

Toyota Venza: Driver Side Power Window does not Operate with Power Window Master Switch

Toyota Venza Service Manual / Window / Glass / Power Window Control System / Driver Side Power Window does not Operate with Power Window Master Switch

DESCRIPTION

When the engine is running or the ignition switch is ON, the power window regulator motor assembly (for driver side) is operated by the power window regulator master switch assembly. The power window regulator motor assembly (for driver side) has motor, regulator, and ECU functions.

HINT:

If the pulse sensor built into the power window regulator motor assembly (for driver side) malfunctions, the power window control system enters fail-safe mode. The remote up/down and auto up/down functions cannot be operated during fail-safe mode. However, the power window can be closed by holding the power window regulator master switch assembly at the auto up position, and opened manually by pushing down the power window regulator master switch assembly.

WIRING DIAGRAM


CAUTION / NOTICE / HINT

NOTICE:

  • The power window control system uses a multiplex communication system (LIN communication system). Inspect the communication function by following How to Proceed with Troubleshooting (See page ). Troubleshoot the power window control
    system after confirming that the communication system is functioning properly.
  • When the power window regulator motor assembly (for driver side) is reinstalled or replaced, the power window control system must be initialized.
  • After a door glass or a door glass run has been replaced, the jam protection function may operate unexpectedly when the auto up function is used. In such cases, the auto up function can be reinitialized by repeating the following operations at least 5 times:
    1. Close the power window by fully pulling up the power window regulator master switch assembly and holding it at the auto up position.
    2. Open the power window by fully pushing down the power window regulator master switch assembly.
  • When the ECU determines that the power window regulator motor assembly (for driver side) has a malfunction, DTC B2311 is set.

PROCEDURE

1.

READ VALUE USING TECHSTREAM (Main Body)

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / Main Body / Data List.

(e) Read the Data List according to the display on the Techstream.

Main Body (Main Body ECU (Driver Side Junction Block Assembly))

Tester Display

Measurement Item/Range

Normal Condition

Diagnostic Note

Communication D-Door Motor

Connection status between power window regulator motor (for driver side) and main body ECU (driver side junction block assembly) / OK or STOP

OK: Normal communication

STOP: Communication stopped

-

OK:

On the Techstream screen, OK is displayed.


NG

GO TO LIN COMMUNICATION SYSTEM (Proceed to How to Proceed with Troubleshooting)


OK

2.

READ VALUE USING TECHSTREAM (D-Door Motor)

(a) Enter the following menus: Body Electrical / D-Door Motor / Data List.

(b) Read the Data List according to the display on the Techstream.

D-Door Motor (Power Window Regulator Motor Assembly (for Driver Side))

Tester Display

Measurement Item/Range

Normal Condition

Diagnostic Note

D Door P/W Up SW

Driver side power window manual up switch signal / ON or OFF

ON: Driver door power window manual up switch operated

OFF: Driver door power window manual up switch not operated

-

D Door P/W Down SW

Driver side power window manual down switch signal / ON or OFF

ON: Driver door power window manual down switch operated

OFF: Driver door power window manual down switch not operated

-

OK:

On the Techstream screen, ON or OFF is displayed accordingly.


NG

GO TO STEP 4


OK

3.

PERFORM ACTIVE TEST USING TECHSTREAM (D-Door Motor)

(a) Enter the following menus: Body Electrical / D-Door Motor / Active Test.

(b) Perform the Active Test according to the display on the Techstream.

D-Door Motor (Power Window Regulator Motor Assembly (for Driver Side))

Tester Display

Test Part

Control Range

Diagnostic Note

Power Window

Power window

OFF / UP / DOWN

-

OK:

Driver side power window operates normally.

CAUTION:

Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function will not operate.


OK

REPLACE MAIN BODY ECU (DRIVER SIDE JUNCTION BLOCK ASSEMBLY)


NG

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Side)

4.

CHECK HARNESS AND CONNECTOR (MASTER SWITCH - DRIVER SIDE MOTOR)

(a) Disconnect the power window regulator master switch assembly connector.


(b) Disconnect the power window regulator motor assembly (for driver side) connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

I6-20 (UP) - I4-10 (UP)

Always

Below 1 Ω

I6-15 (DOWN) - I4-7 (DOWN)

Always

Below 1 Ω

I6-20 (UP) - Body ground

Always

10 kΩ or higher

I6-15 (DOWN) - Body ground

Always

10 kΩ or higher

I4-10 (UP) - Body ground

Always

10 kΩ or higher

I4-7 (DOWN) - Body ground

Always

10 kΩ or higher

Text in Illustration

*1

Front view of wire harness connector

(to Power Window Regulator Master Switch Assembly)

*2

Front view of wire harness connector

(to Power Window Regulator Motor Assembly (for Driver Side))


NG

REPAIR OR REPLACE HARNESS OR CONNECTOR


OK

5.

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

(a) Replace the power window regulator master switch assembly (See page ).



NEXT

6.

CHECK MANUAL UP / DOWN FUNCTION (for Driver Side)

(a) Check that the driver side door power window moves when the manual up/down function of the power window regulator master switch assembly is operated (See page ).


OK:

Driver side manual up/down function is normal.


OK

END (POWER WINDOW REGULATOR MASTER SWITCH WAS DEFECTIVE)


NG

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Side)

Remote Up / Down Function does not Operate
DESCRIPTION When the ignition switch is ON, the power window regulator master switch assembly sends remote up/down signals to each power window regulator motor assembly via the LIN communication ...

Front Passenger Side Power Window does not Operate with Front Passenger Side Power Window Switch
DESCRIPTION When the engine is running or the ignition switch is ON, the power window regulator motor assembly (for front passenger side) is operated by the power window regulator switch assembly ...

Other materials about Toyota Venza:

Terminals Of Ecu
TERMINALS OF ECU 1. CHECK MAIN BODY ECU (DRIVER SIDE JUNCTION BLOCK ASSEMBLY) (a) Disconnect the 2A, 2C and 2F main body ECU (driver side junction block assembly) connectors. (b) Measure the voltage and resistance according to the value(s) in the table ...

Intuitive parking assist
The distance from your vehicle to nearby obstacles when parallel parking or maneuvering into a garage is measured by the sensors and communicated via the multi-information display and a buzzer. Always check the surrounding area when using this system. &n ...

Customize Parameters
CUSTOMIZE PARAMETERS 1. CUSTOMIZING FUNCTION WITH TECHSTREAM (REFERENCE) HINT: When the customer requests a change in a function, first make sure that the function can be customized. Be sure to make a note of the current settings before cust ...

© 2016-2024 Copyright www.tovenza.com

0.1378